You are not logged in. Please login or register.
SoliForum - 3D Printing Community → 3D Printer Discussion → Bubbles under Polyimide Bed tape
what is the secret to not having bubbles in the tape. I have tried starting it and using a squeegee to lay it down
and end up with bubbled. I have used Windex so it wont stick (like applying decals) and when I heat the bed I have bubbles.
I have fought this for years.
I am running a stock Makerbot and do not want to change to glass and hairspray or gluestick.
Thanks
Dale.
poke the bubble with a needle press air out
that is what I do so I take it everyone has that problem when using tape.
I hated the tape that come one my soliddodle and switched to glas ASAP. Thats what I do when I install decals and window tinting
what is the secret to not having bubbles in the tape. I have tried starting it and using a squeegee to lay it down
and end up with bubbled. I have used Windex so it wont stick (like applying decals) and when I heat the bed I have bubbles.
I have fought this for years.I am running a stock Makerbot and do not want to change to glass and hairspray or gluestick.
Thanks
Dale.
I don't use tape, I use glass + glue stick, works great. I do read somewhere mention use soapy water to lay out kapton tape.
Windex is not soapy water, it contain ammonia which generate bubble after almost dry.
Make soapy water from the actual soap or handwashing/dishwashing liquid.
http://forums.reprap.org/read.php?1,124034
https://www.makerbot.com/media-center/2 … ut-bubbles
https://en.wikipedia.org/wiki/Windex
do not want to change to glass and hairspray or gluestick.
Thanks
Dale.
Not sure what your dislike with glass and hairspray is. If you tried it, you ask why you did not do it sooner. The results are great. Plus the side in contact with the glass has a glass smooth finish to it which in some cases is a bonus to the print.
dubbsd wrote:do not want to change to glass and hairspray or gluestick.
Thanks
Dale.Not sure what your dislike with glass and hairspray is. If you tried it, you ask why you did not do it sooner. The results are great. Plus the side in contact with the glass has a glass smooth finish to it which in some cases is a bonus to the print.
I don't seem to be able to see that comment
carl_m1968 wrote:dubbsd wrote:do not want to change to glass and hairspray or gluestick.
Thanks
Dale.Not sure what your dislike with glass and hairspray is. If you tried it, you ask why you did not do it sooner. The results are great. Plus the side in contact with the glass has a glass smooth finish to it which in some cases is a bonus to the print.
I don't seem to be able to see that comment
Very last comment before his signature.
I see now lol
The tape was torn on my used solidoodle , put window glass on it and used hair spray have not looked back .
That was 3 1/2 years ago.
The tape was torn on my used solidoodle , put window glass on it and used hair spray have not looked back .
That was 3 1/2 years ago.
The kapton tape is not meant to last, you will have to replace it sooner or later. I prefer glue stick over hair spray because hair spray can spill to place I don't want them to be, glue stick are lot easy to control.
Tin Falcon wrote:The tape was torn on my used solidoodle , put window glass on it and used hair spray have not looked back .
That was 3 1/2 years ago.The kapton tape is not meant to last, you will have to replace it sooner or later. I prefer glue stick over hair spray because hair spray can spill to place I don't want them to be, glue stick are lot easy to control.
When you use hair spray you are supposed to spray the glass before you put in the printer. I personally use mirror panels. I like the look of the reflection. You also should use real spray and not a pump type that dries slower. By doing it this way there is no way the spray can get into the printer or it's mechanics. Glue is fine but it needs to be reapplied more often than hair spray. I can do thirty prints on one coat of hairspray.
When you use hair spray you are supposed to spray the glass before you put in the printer. I personally use mirror panels. I like the look of the reflection. You also should use real spray and not a pump type that dries slower. By doing it this way there is no way the spray can get into the printer or it's mechanics. Glue is fine but it needs to be reapplied more often than hair spray. I can do thirty prints on one coat of hairspray.
True, Glue only last about 5 prints, then I have to brush some water to make the glue evenly redistributed again. Take glass plate outside of printer is lots of pain, but not too bad if you only have to do it every 30 prints.
carl_m1968 wrote:When you use hair spray you are supposed to spray the glass before you put in the printer. I personally use mirror panels. I like the look of the reflection. You also should use real spray and not a pump type that dries slower. By doing it this way there is no way the spray can get into the printer or it's mechanics. Glue is fine but it needs to be reapplied more often than hair spray. I can do thirty prints on one coat of hairspray.
True, Glue only last about 5 prints, then I have to brush some water to make the glue evenly redistributed again. Take glass plate outside of printer is lots of pain, but not too bad if you only have to do it every 30 prints.
thats not true at all. I use glass and elmers glue. I only have to apply glue once a month or so and i print daily
thats not true at all. I use glass and elmers glue. I only have to apply glue once a month or so and i print daily
I agree it will last longer, but I don't take chances, I don't have to apply glue every 5 prints, I just brush the bed with wet brush to make it more average.
SoliForum - 3D Printing Community → 3D Printer Discussion → Bubbles under Polyimide Bed tape
Powered by PunBB, supported by Informer Technologies, Inc.
