Topic: sorceress figurine
one of my prototype for heroic fantasy display
you can take it on thingiverse
http://www.thingiverse.com/thing:47472
have fun 
Re: sorceress figurine
Nice work! That turned out really good
- ysb
- Member
- Offline
Re: sorceress figurine
thank you.. i will try to do a supportless for the next one...
Re: sorceress figurine
Better be something without a lot of hanging drapery.
That seems to be the kicker with modelling. Anything that hangs off that drastically requires support. Unless you're doing it piecemeal in which case you have to design it to look good printed separately (not usually too much of a problem).
- ysb
- Member
- Offline
Re: sorceress figurine
hanging drapery on a woman is more fun 
Re: sorceress figurine
ysb wrote:
hanging drapery on a woman is more fun
Where are you located? We'd love to see this print.
Former Solidoodle employee, no longer associated with the company.
- Brad
- Administrator
- Offline
Re: sorceress figurine
Looks really good, you did an awesome job removing the support material. I always leave little nubs on where the support material was and have a hard time getting it off... perhaps I need some sand paper.
8 2013-02-15 01:49:52 (edited by ysb 2013-02-15 01:55:34)
- ysb
- Member
- Offline
Re: sorceress figurine
solidoodlesupport wrote:
ysb wrote:hanging drapery on a woman is more fun
Where are you located? We'd love to see this print.
quebec city ...it's a bit far away from your office i think
@brad : use the support in medium mode of kisslicer with grid (raft) ... it's far better than other slicer... it let a very light contact point... ok.. i forget to say that the model is very well build too ( # joke inside #) ;-)
Re: sorceress figurine
ysb you might look at daz3d and hexagon 2 they are free services that has nive content
- ysb
- Member
- Offline
Re: sorceress figurine
Manx wrote:
ysb you might look at daz3d and hexagon 2 they are free services that has nive content
i already use hexagon 2.5 . i prefer poser pro over daz studio and i try to avoid daz3d content for 3dprinting. daz doesn't allow you to use their models and give away the stl after. they only allow you to make digital pictures with them.
11 2013-06-04 23:54:46 (edited by LdyMox 2013-06-04 23:55:25)
- LdyMox
- Member
- Offline
Re: sorceress figurine
In red transparent PLA. Still need to make her base
Tammy
Solidoodle 2
E3Dv6 Hotend, MK5 v6 version, Glass Bed, Anti Z backlash slop nut, SureStepr SD8825 1/32 Extruder Driver, makeshift breakaway plexiglass case; . L-Cheapo 3.8 Watt Laser Attachment w/Custom built enclosure
From Buffalo, NY, USA
Solidoodle 2
E3Dv6 Hotend, MK5 v6 version, Glass Bed, Anti Z backlash slop nut, SureStepr SD8825 1/32 Extruder Driver, makeshift breakaway plexiglass case; . L-Cheapo 3.8 Watt Laser Attachment w/Custom built enclosure
From Buffalo, NY, USA
12 2013-06-05 10:18:28 (edited by ysb 2013-06-05 10:20:24)
- ysb
- Member
- Offline
Re: sorceress figurine
Seem to be well printed but it's difficult to say with this color.. hope you like it
Ps its this model
www.soliforum.com/topic/2125/sorceress-v2/
- LdyMox
- Member
- Offline
Re: sorceress figurine
Opps. Well looked a lot like it.
The biggest problem with the print was in the face since it was PLA had a few droops. Otherwise came out well.
Tammy
Solidoodle 2
E3Dv6 Hotend, MK5 v6 version, Glass Bed, Anti Z backlash slop nut, SureStepr SD8825 1/32 Extruder Driver, makeshift breakaway plexiglass case; . L-Cheapo 3.8 Watt Laser Attachment w/Custom built enclosure
From Buffalo, NY, USA
Solidoodle 2
E3Dv6 Hotend, MK5 v6 version, Glass Bed, Anti Z backlash slop nut, SureStepr SD8825 1/32 Extruder Driver, makeshift breakaway plexiglass case; . L-Cheapo 3.8 Watt Laser Attachment w/Custom built enclosure
From Buffalo, NY, USA