1 Topic by hammade90

  • hammade90
  • Member
  • Offline
  • From: US-Eastcoast
  • Registered: 2014-09-27
  • Posts: 72

Topic: Sang 1.3a help

Binary sketch size: 54588 bytes (of a 63488 byte maximum)
avrdude: stk500_getsync(): not in sync: resp=0x00
avrdude: stk500_disable(): protocol error, expect=0x14, resp=0x51

"SD3" 5/02/13 03943, RAMPS 1.6+, Enclosed,  360W12V30A PSU, E3DV6(new model), Nema17 .9 (E)  Over kill Y brackets, Y drive Bearings, Y-Direct Drive, Hale bed heater on 3/16 aluminum, Lawsy Carriage upgrade, gt2 20T Pulleys.

2 Reply by heartless

  • heartless
  • heartless
  • Member
  • Offline
  • From: Northcentral Wisconsin
  • Registered: 2015-04-08
  • Posts: 2,152

Re: Sang 1.3a help

do you have your Arduino set up properly?
Correct board selected?
Correct processor selected?
Correct COM port selected?

SD4 #1 & #2 - Lawsy carriages, E3D v6, Rumba controller board, mirror bed plate, X motor fan, upgraded PSU & Mica bed heater
SD4 #3 - in the works ~ Folgertech FT-5, rev 1
Printit Industries Beta Tester - Horizon H1

3 Reply by hammade90

  • hammade90
  • Member
  • Offline
  • From: US-Eastcoast
  • Registered: 2014-09-27
  • Posts: 72

Re: Sang 1.3a help

heartless wrote:

do you have your Arduino set up properly?
Correct board selected?
Correct processor selected?
Correct COM port selected?

everything was working the other day.

"SD3" 5/02/13 03943, RAMPS 1.6+, Enclosed,  360W12V30A PSU, E3DV6(new model), Nema17 .9 (E)  Over kill Y brackets, Y drive Bearings, Y-Direct Drive, Hale bed heater on 3/16 aluminum, Lawsy Carriage upgrade, gt2 20T Pulleys.

4 Reply by yizhou.he

  • yizhou.he
  • yizhou.he
  • Member
  • Offline
  • From: Boston, MA
  • Registered: 2017-07-05
  • Posts: 1,322

Re: Sang 1.3a help

make sure no other apps (repetier host or whatever you use to control the printer) connected to printer. Disconnect or close other apps before attempt upload.

(Da Vinci 1.0, Jr. 1.0 RAMPS, miniMaker) X4, (Creality CR-10S, CR-10 mini, Ender-3) X4, Anycubic MEGA X4, Anycubic Chrion X1, ADMILAB Gantry X2 (MonoPrice Maker Select V2, Plus, Ultimate)X4--Select mini X1, Anycubic photon X4, Wanhao duplicate D7 X1.
iNSTONE Inventor Pro X2, CTC Dual X2, ANET-A8, Hictop 3DP-11, Solidoodle Press, FLSUN I3 2017X1

5 Reply by heartless

  • heartless
  • heartless
  • Member
  • Offline
  • From: Northcentral Wisconsin
  • Registered: 2015-04-08
  • Posts: 2,152

Re: Sang 1.3a help

hammade90 wrote:
heartless wrote:

do you have your Arduino set up properly?
Correct board selected?
Correct processor selected?
Correct COM port selected?

everything was working the other day.

That does not mean something didn't somehow get changed - check it all to verify.

also, main power "should" be shut down, for flashing you should only need USB power to the board
and no other programs connected to the printer (close RH, or whatever you use)

SD4 #1 & #2 - Lawsy carriages, E3D v6, Rumba controller board, mirror bed plate, X motor fan, upgraded PSU & Mica bed heater
SD4 #3 - in the works ~ Folgertech FT-5, rev 1
Printit Industries Beta Tester - Horizon H1