51 Reply by karltinsly

  • karltinsly
  • Member
  • Offline
  • Registered: 2014-12-17
  • Posts: 44

Re: Da Vinci to Ramps - bed thermistor question

Will do. Thanks!

52 Reply by leadpan

  • leadpan
  • Member
  • Offline
  • Registered: 2015-05-07
  • Posts: 24

Re: Da Vinci to Ramps - bed thermistor question

Karltinsly, i'm also upgrade to Ramp1.4.
How did you determine which wires are positive and negative on stepper motors?

53 Reply by carl_m1968

  • carl_m1968
  • carl_m1968
  • Member
  • Offline
  • From: Far North almost not Dallas
  • Registered: 2014-10-17
  • Posts: 6,512

Re: Da Vinci to Ramps - bed thermistor question

leadpan wrote:

Karltinsly, i'm also upgrade to Ramp1.4.
How did you determine which wires are positive and negative on stepper motors?

They are are marked on the drivers and you can see the traces from the drivers leading to each pin of the connector on the mainboard. Thats how I did mine.

Printing since 2009 and still love it!
Anycubic 4MAX best $225 ever invested.
Voxelabs Proxima SLA. 6 inch 2k Mono LCD.
Anycubic Predator, massive Delta machine. 450 x 370 print envelope.

54 Reply by leadpan

  • leadpan
  • Member
  • Offline
  • Registered: 2015-05-07
  • Posts: 24

Re: Da Vinci to Ramps - bed thermistor question

Thanks Carl for that tip.
Is it possible to use stock optical stops on my Da Vinci 2.0?

55 Reply by leadpan (edited by leadpan 2016-07-05 17:54:38)

  • leadpan
  • Member
  • Offline
  • Registered: 2015-05-07
  • Posts: 24

Re: Da Vinci to Ramps - bed thermistor question

Not sure if I need to replace the stock Davinci 2.0 power supply or not? Will it burn out the mega2560?
Almost ready to compile and power up.http://soliforum.com/i/?5WypRQx.jpg
http://soliforum.com/i/?c1J1gwd.jpg

56 Reply by not1ofthepack (edited by not1ofthepack 2016-09-24 14:12:44)

  • not1ofthepack
  • Newbie
  • Offline
  • Registered: 2015-06-05
  • Posts: 3

Re: Da Vinci to Ramps - bed thermistor question

Here are a few of the mods I have done to my  XYZ DaVinci 1.0,    Replaced the bed so it has 4 corners I can adjust the height, I also added a four port terminal strip at the bottom in case I would like to change the heatbed or sensor easily.   Next is the side filament load, loaded via a Bowden setup.    Replaced the mobo with a Ramps 1.4 and added mechanical endstops   On top added another terminal strip for hotend, sensor,  12v extra, fan control, all for easy replacements.   Replaced x carriage to accommodate an E3D V6  and put a servo auto leveling on it as well.

Post's attachments

XYZ DaVinci 1.0 Mod 4Port bed.jpg
XYZ DaVinci 1.0 Mod 4Port bed.jpg 76.21 kb, file has never been downloaded. 

XYZ DaVinci 1.0 Mod Bed conversion.jpg
XYZ DaVinci 1.0 Mod Bed conversion.jpg 71.43 kb, file has never been downloaded. 

XYZ DaVinci 1.0 Mod Power Strip.jpg 81.46 kb, 1 downloads since 2016-09-24 

XYZ DaVinci 1.0 Mod Ramps 1.4.jpg
XYZ DaVinci 1.0 Mod Ramps 1.4.jpg 77.35 kb, file has never been downloaded. 

XYZ DaVinci 1.0 Mod X carriadge.jpg
XYZ DaVinci 1.0 Mod X carriadge.jpg 78.41 kb, file has never been downloaded. 

You don't have the permssions to download the attachments of this post.

57 Reply by not1ofthepack

  • not1ofthepack
  • Newbie
  • Offline
  • Registered: 2015-06-05
  • Posts: 3

Re: Da Vinci to Ramps - bed thermistor question

continue of pictures

Post's attachments

XYZ DaVinci 1.0 Mod X endstop.jpg
XYZ DaVinci 1.0 Mod X endstop.jpg 81.65 kb, file has never been downloaded. 

XYZ DaVinci 1.0 Mod Y endstop.jpg
XYZ DaVinci 1.0 Mod Y endstop.jpg 82.41 kb, file has never been downloaded. 

You don't have the permssions to download the attachments of this post.

58 Reply by leadpan

  • leadpan
  • Member
  • Offline
  • Registered: 2015-05-07
  • Posts: 24

Re: Da Vinci to Ramps - bed thermistor question

If you're using Marlin, can you share the configure.h file?