You are not logged in. Please login or register.
SoliForum - 3D Printing Community → Solidoodle Discussion → SOLVED-SD4 extruder problems kind of
Its in that pic it says RUMBA/TAURINO-ATmega2560 compatable (com3)
So you're good there then. Can you post the console output next, without sending any additional commands after connecting? Would be good to know what commands it's waiting for.
So you're good there then. Can you post the console output next, without sending any additional commands after connecting? Would be good to know what commands it's waiting for.
What is that? Forgove my naivness...if you mean under manual control it says 1 command waiting
check reset on connect to DISABLED
So you're good there then. Can you post the console output next, without sending any additional commands after connecting? Would be good to know what commands it's waiting for.
It shouldn't matter what it is waiting for it is waiting because it isn't connected to R-H
Im DL RH version you have now and will change that. in new version 1.0.6 the board flashes yellow light...but in older 0.85b when printer is connected light stays lit...
Im DL RH version you have now and will change that. in new version 1.0.6 the board flashes yellow light...but in older 0.85b when printer is connected light stays lit...
Keep at it!!! This is most likely a simple fix we just can't see it until you put it in front of us 
Nvm version you have crashes...im running win 8.1 64bit btw, if that matters anywhere along the road...and of course the RH where light stays lit foesnt have option (not that I see to disable that setting) only on newer 1.0.6
You don't want that version that is an old screen shot go for 95f
Sorry about that I had to go back and look at the picture to see what version you were talking about.
Will DL that..also in Pronterface, when i hit connect it just sits at (connecting...) if i inplug it it recognizes it was unplugged yet wont connect....hmmm idk if inflashed it correctly maybe not!? Such a noob i am
95f does same thing....crashes when I go to run it sighhhhhh
As promised here are my configuration files. Note that in configuration_adv.h, I have it set up to run the fans for 10 minutes after the steppers shut down, but you can shorten this if you want. My board is still inside the enclosure which gets hot so I do this to make sure they get plenty of time to cool down. The steps per mm are for 1/32 microstepping in here, so keep that in mind. I used 1/32 on X,Y,Z,E.
PS: You will need a fan pointed at the board or your motors will start skipping. Here is a little 40mm fan mount I made that will snap onto the SD4 motherboard mount. Print it on its side and it wont need supports.
Thank you guys a ton...seriously I appreciate this to no end...will dig into this in bit need break now. Or else this thing is going flying through window 
We posted at the same time so just posting again to make sure you see above
I had to run out snd will post pics of how I have stuff hooked up (although I'm leaning more towards software issue) but for the endstops I used meter, set to continuity and when i found wire that buzzed and than stopped when i hit switch I hooked that up to - (c on the switch, and the other to S)....in case that was wrong I also reversed plug so the two wires would be on the other the c on the s...still got nowhere...also will the terminals for extruder knly get voltage once board isnTRULY recognized by RH...a few posts back I said that whole bank has no voltage, stepper drivers do and 5v and 12v pin outs towards top next to first motor hookup....the printeboard had to go and take a shit on me....I was gunna do this anyway but figured i wouldnt want to punch my cat in the face out of frustration
Will DL that..also in Pronterface, when i hit connect it just sits at (connecting...) if i inplug it it recognizes it was unplugged yet wont connect....hmmm idk if inflashed it correctly maybe not!? Such a noob i am
We were all noobs at one point
When you flashed it what version did you load and did you select the correct board in configuration.h?
I have to look when I get back Onnversion but board inwant to say mega 2560, also cooied jagos config files assuming I effed up, and that still got me nowhere. Also using arduino 0022
Jago can you toss up a screen shot of the configuration.h where Rumba (80 I think it is) is selected?
I'm realizing now that Arduino IDE doesn't show line numbers... (edit: it's on the bottom of the screen)
Also, make sure you match the baud rate with the firmware! By default, it is 250,000 in the firmware. Make sure RH matches.
One additional note: my configuration.h file is set up for the e3d, so if you copy my file directly make sure you set it back to the defaults.
Yeah im doing e3d but need to print bodybfor it...along w a list of other things inwant need before that. Just wanna get this baby going. Will check baud, and compare files just headed back to the "lab" now
Also if im using the 360w 30a multi bank PSU whih I am, set it to ATX?
Only if you plan on having the ATX remotely controlled. if not than just leave that alone.
OneMoreCast wrote:Will DL that..also in Pronterface, when i hit connect it just sits at (connecting...) if i inplug it it recognizes it was unplugged yet wont connect....hmmm idk if inflashed it correctly maybe not!? Such a noob i am
We were all noobs at one point
When you flashed it what version did you load and did you select the correct board in configuration.h?
Went to github and downloaded, its marlin development, ill guess this is incorrect one...:|
https://github.com/ozadr1an/Solidoodle-Marlin_v1/
You want this one
SoliForum - 3D Printing Community → Solidoodle Discussion → SOLVED-SD4 extruder problems kind of
Powered by PunBB, supported by Informer Technologies, Inc.
