1 Topic by hammade90

  • hammade90
  • Member
  • Offline
  • From: US-Eastcoast
  • Registered: 2014-09-27
  • Posts: 72

Topic: SD3 Sang 1.3a Firmware update help needed please & thank you

Hello everyone, I Have a SD3 only mod/upgrade i've done so far was replace stock psu today. I replaced it with the supernight psu. Printer is also enclosed. All i'd like to do is update my firmware for now. The Board is the Sang 1.3a. Can someone point me in the right direction, I seem to be having problems finding my own way 0__o...feeling De ta duh:[

"SD3" 5/02/13 03943, RAMPS 1.6+, Enclosed,  360W12V30A PSU, E3DV6(new model), Nema17 .9 (E)  Over kill Y brackets, Y drive Bearings, Y-Direct Drive, Hale bed heater on 3/16 aluminum, Lawsy Carriage upgrade, gt2 20T Pulleys.

2 Reply by satman49

  • satman49
  • Member
  • Offline
  • From: virginia
  • Registered: 2012-12-28
  • Posts: 867

Re: SD3 Sang 1.3a Firmware update help needed please & thank you

this should help as I have the same board http://www.soliwiki.com/Updating_Solidoodle_Firmware

SD3, E3D hotend,linear bearing on x/y axis',pillow block bearing on y conneting rod, ball bearngs on front y axis, fan on y stepper motor.

3 Reply by hammade90

  • hammade90
  • Member
  • Offline
  • From: US-Eastcoast
  • Registered: 2014-09-27
  • Posts: 72

Re: SD3 Sang 1.3a Firmware update help needed please & thank you

Thanks satman46, I'll keep you updated.

"SD3" 5/02/13 03943, RAMPS 1.6+, Enclosed,  360W12V30A PSU, E3DV6(new model), Nema17 .9 (E)  Over kill Y brackets, Y drive Bearings, Y-Direct Drive, Hale bed heater on 3/16 aluminum, Lawsy Carriage upgrade, gt2 20T Pulleys.

4 Reply by wardjr

  • wardjr
  • wardjr
  • Moderator
  • Offline
  • From: Minnesota
  • Registered: 2013-06-10
  • Posts: 5,624

Re: SD3 Sang 1.3a Firmware update help needed please & thank you

hammade90 wrote:

Thanks satman46, I'll keep you updated.

Yep the Sang is fairly straightforward.  If you have questions just ask.  It may be worth the extra effort to increase the max temps for the extruder of you have future plans of upgrading to an E3d.

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

wardjr's Website

5 Reply by hammade90

  • hammade90
  • Member
  • Offline
  • From: US-Eastcoast
  • Registered: 2014-09-27
  • Posts: 72

Re: SD3 Sang 1.3a Firmware update help needed please & thank you

Which Board is used on the SD3 644 1224p 8mhz or 1224p 16mhz? How can i Tell what i have?

"SD3" 5/02/13 03943, RAMPS 1.6+, Enclosed,  360W12V30A PSU, E3DV6(new model), Nema17 .9 (E)  Over kill Y brackets, Y drive Bearings, Y-Direct Drive, Hale bed heater on 3/16 aluminum, Lawsy Carriage upgrade, gt2 20T Pulleys.

6 Reply by hammade90

  • hammade90
  • Member
  • Offline
  • From: US-Eastcoast
  • Registered: 2014-09-27
  • Posts: 72

Re: SD3 Sang 1.3a Firmware update help needed please & thank you

Now in repetier, Printer info says machine is mendel...should it not state Solidoodle...what am i doing wrong?

"SD3" 5/02/13 03943, RAMPS 1.6+, Enclosed,  360W12V30A PSU, E3DV6(new model), Nema17 .9 (E)  Over kill Y brackets, Y drive Bearings, Y-Direct Drive, Hale bed heater on 3/16 aluminum, Lawsy Carriage upgrade, gt2 20T Pulleys.

7 Reply by hammade90

  • hammade90
  • Member
  • Offline
  • From: US-Eastcoast
  • Registered: 2014-09-27
  • Posts: 72

Re: SD3 Sang 1.3a Firmware update help needed please & thank you

These firmware updates are incredible! Unbelievable improvements, Print bed just heated up from 22C to 95c in T minus TEN MINUTES compaired to previous 40+minutes! WOW:D

Only upgrade is i just wired the supernight psu up earlier today. I Have images and screen shots to post but im not understanding how??

"SD3" 5/02/13 03943, RAMPS 1.6+, Enclosed,  360W12V30A PSU, E3DV6(new model), Nema17 .9 (E)  Over kill Y brackets, Y drive Bearings, Y-Direct Drive, Hale bed heater on 3/16 aluminum, Lawsy Carriage upgrade, gt2 20T Pulleys.

8 Reply by wardjr

  • wardjr
  • wardjr
  • Moderator
  • Offline
  • From: Minnesota
  • Registered: 2013-06-10
  • Posts: 5,624

Re: SD3 Sang 1.3a Firmware update help needed please & thank you

Better heat time is from a better PSU.
Post pictures using imgur or the choose file and then add file buttons below.

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

wardjr's Website