print of YSB Anais Horse

**ggunners** · 2014-01-22 19:38:42

ggunners
Member
Offline

From: Chantilly, VA USA
Registered: 2013-12-03
Posts: 170

Topic: print of YSB Anais Horse

First, thank you so much YSB for a nice 3D model. You are a terrific artist and your attention to detail and making a 3D .stl file that prints well and does not need supports is fantastic. I will be pressing the big button soon.

I resized it to 60% to better fit my time constraints and my SD2 bed. .200 height. Hope you like the results. -- ggunners

Post's attachments

20140122_113659.jpg
20140122_113659.jpg 50.53 kb, file has never been downloaded.

20140122_113803.jpg
20140122_113803.jpg 55.11 kb, file has never been downloaded.

20140122_114139.jpg 34.88 kb, file has never been downloaded.

You don't have the permssions to download the attachments of this post.

SD2 Expert stock, ABS fume fan,
XYZ DaVinci 1.0 stock ABS, Simplify3D
QUBD Two-Up PLA, new 3D printed X gantry, Y idler, flex z coupler, extruder mount, E3D Lite

**ysb** · 2014-01-23 14:22:28

ysb
Member
Offline

From: quebec, canada
Registered: 2012-08-09
Posts: 1,164

Re: print of YSB Anais Horse

thanks for your comments

i always like to see model with a different scale than my 'original'..(to see if it is 'tolerant to resizing')

what is you layer height for this model ? the print is very clean

Find all my 3D printable models here
Game of ropes 2 online..Adult only

**ggunners** · 2014-01-23 14:33:57

ggunners
Member
Offline

From: Chantilly, VA USA
Registered: 2013-12-03
Posts: 170

Re: print of YSB Anais Horse

Hi ysb. The layer height is 200 microns.

I was amazed at how smooth the model printed and after a careful close up examination, I really feel that you have mastered the 3D printing medium. I am hoping to gain the same knowledge and expertise as I learn 3D design for solids.

I have many 3D airplanes flying in RC simulators, but those are much different. There you use very low polygon counts with image maps and do not have to worry about manifold objects.

I will certainly print Anais to sit with her horse.

-- ggunners

SD2 Expert stock, ABS fume fan,
XYZ DaVinci 1.0 stock ABS, Simplify3D
QUBD Two-Up PLA, new 3D printed X gantry, Y idler, flex z coupler, extruder mount, E3D Lite

**ggunners** · 2014-02-03 21:31:34

ggunners
Member
Offline

From: Chantilly, VA USA
Registered: 2013-12-03
Posts: 170

Re: print of YSB Anais Horse

I finally got the time to print Anais herself also 60 percent at 200 microns to keep her and her horse to scale.

Unfortunately, a few areas of the print suffered from being downscaled. Her hand almost fell apart and was much too thin after reducing the size. Also, her ears did not print well and her face lost some detail. Almost everything else printed pretty well. I may try her again at 100 microns. -- ggunners

Post's attachments

20140203_120343.jpg
20140203_120343.jpg 59.57 kb, file has never been downloaded.

Anais-views.jpg 65.15 kb, file has never been downloaded.

You don't have the permssions to download the attachments of this post.

SD2 Expert stock, ABS fume fan,
XYZ DaVinci 1.0 stock ABS, Simplify3D
QUBD Two-Up PLA, new 3D printed X gantry, Y idler, flex z coupler, extruder mount, E3D Lite

**DesignerFred** · 2014-02-05 21:44:50

DesignerFred
Member
Offline

From: France
Registered: 2013-03-19
Posts: 264

Re: print of YSB Anais Horse

Nice prints...

www.designerfred.fr before: Solidoodle 2 + E3D v6 now: MeCreator II and OLO 3D

print of YSB Anais Horse

Posts: 5

1 Topic by ggunners 2014-01-22 19:38:42 (edited by ggunners 2014-02-12 20:01:24)

Topic: print of YSB Anais Horse

2 Reply by ysb 2014-01-23 14:22:28

Re: print of YSB Anais Horse

3 Reply by ggunners 2014-01-23 14:33:57

Re: print of YSB Anais Horse

4 Reply by ggunners 2014-02-03 21:31:34

Re: print of YSB Anais Horse

5 Reply by DesignerFred 2014-02-05 21:44:50

Re: print of YSB Anais Horse

Posts: 5