1 Topic by Ironsight

  • Ironsight
  • Member
  • Offline
  • From: Toronto, ON
  • Registered: 2014-12-21
  • Posts: 17

Topic: How to add the Hysteresis Fix?

I searched for Hysteresis Fix in the forums and found a thread on it but it is 2 years old. I tried to follow it but I don't understand how to even do step 2. "Add some cases to the switch statement in process_commands in Marlin.pde. Search for "case 115: // M115" and insert the following lines before that line..."
Looked further into it and I can't even find planner.cpp

The link is here: http://www.soliforum.com/topic/313/hysteresis-fix/

I think my firmware is up to date, its called Marlin V1. I tried manually sending the M98 command but nothing comes back.

Can anyone help me figure out how to implement the hysteresis fix?

SD4 with Lawsy Carriages, Flanged bearings + Y-Drive Pillow Block, Adjustable Y-Idlers, Z-axis Ballscrew. Printing ABS on ceramic tile w/ hairspray.

Future Plans: GT2 Belts/Pulleys, E3D lite6

2 Reply by wardjr

  • wardjr
  • wardjr
  • Moderator
  • Offline
  • From: Minnesota
  • Registered: 2013-06-10
  • Posts: 5,624

Re: How to add the Hysteresis Fix?

You'll need this firmware https://github.com/ozadr1an/Solidoodle- … in_v1_beta
Then just enable it in configuration.h
Change values as needed and that's it.

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

wardjr's Website

3 Reply by Ironsight

  • Ironsight
  • Member
  • Offline
  • From: Toronto, ON
  • Registered: 2014-12-21
  • Posts: 17

Re: How to add the Hysteresis Fix?

I just double checked and I do have the Marlin V1 beta firmware flashed.

How do I enable it in configuration.h? The only hysteresis I see mentioned is for the bed temperature.

SD4 with Lawsy Carriages, Flanged bearings + Y-Drive Pillow Block, Adjustable Y-Idlers, Z-axis Ballscrew. Printing ABS on ceramic tile w/ hairspray.

Future Plans: GT2 Belts/Pulleys, E3D lite6

4 Reply by wardjr

  • wardjr
  • wardjr
  • Moderator
  • Offline
  • From: Minnesota
  • Registered: 2013-06-10
  • Posts: 5,624

Re: How to add the Hysteresis Fix?

But is it that exact one?  There are two that show up as v1 beta.
Either way I won't be near a computer until the AM then I can post up screen shots.

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

wardjr's Website

5 Reply by wardjr

  • wardjr
  • wardjr
  • Moderator
  • Offline
  • From: Minnesota
  • Registered: 2013-06-10
  • Posts: 5,624

Re: How to add the Hysteresis Fix?

Enable it here
http://i.imgur.com/XuI0zQn.jpg

Then enter your values here
http://i.imgur.com/Ty5B25A.jpg

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

wardjr's Website

6 Reply by Ironsight

  • Ironsight
  • Member
  • Offline
  • From: Toronto, ON
  • Registered: 2014-12-21
  • Posts: 17

Re: How to add the Hysteresis Fix?

Okay I got it working now. That was way easier than I expected. Thanks!

SD4 with Lawsy Carriages, Flanged bearings + Y-Drive Pillow Block, Adjustable Y-Idlers, Z-axis Ballscrew. Printing ABS on ceramic tile w/ hairspray.

Future Plans: GT2 Belts/Pulleys, E3D lite6