1 Topic by khoabui05

  • khoabui05
  • Member
  • Offline
  • Registered: 2015-01-29
  • Posts: 23

Topic: Da Vinci 1.0 AiO All-in-One 3D Printer

I was wondering on this model can you still flash the firmware, so that you don't have to buy the xyz filament cartridge?
if yes, do you still use the 1.0 firmware?

or should i use the method of resetting eprom chip on the cartridge?

2 Reply by resonance01

  • resonance01
  • Newbie
  • Offline
  • Registered: 2015-02-04
  • Posts: 4

Re: Da Vinci 1.0 AiO All-in-One 3D Printer

Just got hold of a da Vinci aio and wondered this myself, I thought it was the same machine as the normal version 1 but was mistaken. Will do a little more digging

3 Reply by hoppy

  • hoppy
  • Newbie
  • Offline
  • Registered: 2015-02-24
  • Posts: 1

Re: Da Vinci 1.0 AiO All-in-One 3D Printer

go to wc-tek.com they can help you

4 Reply by resonance01

  • resonance01
  • Newbie
  • Offline
  • Registered: 2015-02-04
  • Posts: 4

Re: Da Vinci 1.0 AiO All-in-One 3D Printer

I forgot about this post, I ended up getting the xyzerocart Bluetooth connector for this printer, learnt a lot about 3d printing since.. Now running 1kg rolls of abs/pla.

5 Reply by kev0175

  • kev0175
  • Member
  • Offline
  • Registered: 2015-02-17
  • Posts: 146

Re: Da Vinci 1.0 AiO All-in-One 3D Printer

resonance01 wrote:

I forgot about this post, I ended up getting the xyzerocart Bluetooth connector for this printer, learnt a lot about 3d printing since.. Now running 1kg rolls of abs/pla.


What firmware do you have on your printer and is the printer overriding some of your temperatures settings when using the xyzerocart?

Da Vinci  AiO with firmware 1.1.1 using xyzscan 1.1.18
E3Dv6 hotend with custom carriage with Borosilicate glass bed
123D Design and Simplify3D, Replaced PS with a Solidgear Flex320
Zerokart resetter,  Installed a Extruder Controller for higher temps

6 Reply by resonance01

  • resonance01
  • Newbie
  • Offline
  • Registered: 2015-02-04
  • Posts: 4

Re: Da Vinci 1.0 AiO All-in-One 3D Printer

I'm using 1.0a firmware (the one that it came with) the xyzerocart controls everything including both temps. Looks good as far as I can see.

7 Reply by kev0175

  • kev0175
  • Member
  • Offline
  • Registered: 2015-02-17
  • Posts: 146

Re: Da Vinci 1.0 AiO All-in-One 3D Printer

resonance01 wrote:

I'm using 1.0a firmware (the one that it came with) the xyzerocart controls everything including both temps. Looks good as far as I can see.


OK I have the 1.0 AIO with firmware 1.1.1 and it looks like my temp settings is in my firmware because if I set my temps past 230c with the xyzerocart or any resetter  the extruder will not heat up.

Da Vinci  AiO with firmware 1.1.1 using xyzscan 1.1.18
E3Dv6 hotend with custom carriage with Borosilicate glass bed
123D Design and Simplify3D, Replaced PS with a Solidgear Flex320
Zerokart resetter,  Installed a Extruder Controller for higher temps

8 Reply by resonance01

  • resonance01
  • Newbie
  • Offline
  • Registered: 2015-02-04
  • Posts: 4

Re: Da Vinci 1.0 AiO All-in-One 3D Printer

I'll double check mine and get back to you, are you using pla then? I was using default heat settings as I'm testing some different abs

9 Reply by kev0175

  • kev0175
  • Member
  • Offline
  • Registered: 2015-02-17
  • Posts: 146

Re: Da Vinci 1.0 AiO All-in-One 3D Printer

Yes I am and different abs. pla didn't work kept swelling

Da Vinci  AiO with firmware 1.1.1 using xyzscan 1.1.18
E3Dv6 hotend with custom carriage with Borosilicate glass bed
123D Design and Simplify3D, Replaced PS with a Solidgear Flex320
Zerokart resetter,  Installed a Extruder Controller for higher temps