1 Topic by lsgraphics

  • lsgraphics
  • Member
  • Offline
  • Registered: 2014-02-24
  • Posts: 27

Topic: problem with stl file

Having a problem with stl file.   Sent thru netfabb gives me an error of mesh calculation failed calculation terminated.  Thanks for any help

Post's attachments

IMG_3713.JPG 2.57 mb, file has never been downloaded. 

IMG_3714.JPG 1.85 mb, file has never been downloaded. 

IMG_3715.JPG 2.09 mb, file has never been downloaded. 

IMG_3716.JPG
IMG_3716.JPG 2.51 mb, file has never been downloaded. 

You don't have the permssions to download the attachments of this post.

2 Reply by pirvan

  • pirvan
  • pirvan
  • Member
  • Offline
  • From: San Francisco
  • Registered: 2013-03-27
  • Posts: 1,797

Re: problem with stl file

It would help if you were to post the STL so we could take a look at it.

To print or, 3D print, that is the question...
SD3 printer w/too many mods,  Printrbot Simple Maker Ed.,  FormLabs Form 1+
AnyCubic Photon, Shining 3D EinScan-S & Atlas 3D scanners...
...and too much time on my hands.

3 Reply by wire10ga

  • wire10ga
  • wire10ga
  • Member
  • Offline
  • From: Arkansas
  • Registered: 2012-09-14
  • Posts: 665

Re: problem with stl file

+1

SD2 - Glass Bed, Fans on PCB and Y motor, Custom enclosure
Slicer - Simplify3D

wire10ga's Website

4 Reply by lsgraphics

  • lsgraphics
  • Member
  • Offline
  • Registered: 2014-02-24
  • Posts: 27

Re: problem with stl file

Tried putting file on here and it wouldn't let me kept getting an error message

5 Reply by lsgraphics

  • lsgraphics
  • Member
  • Offline
  • Registered: 2014-02-24
  • Posts: 27

Re: problem with stl file

Warning! The following errors must be corrected before your message can be posted:

    The selected file was too large to upload. The server didn't allow the upload.

This is the error i am receiving

6 Reply by n2ri

  • n2ri
  • Member
  • Offline
  • From: St Louis MO USA area
  • Registered: 2013-02-03
  • Posts: 2,539

Re: problem with stl file

likely just bad or corrupted download file
maybe go to site its from and check with author

Solidoodle 2 with Deluxe kit cover & glass bed with heater. and 2nd board SD2 used not 3rd and alum platform not installed yet still wood. also need cooling fan installed to board. use Repetier Host couple vers. Slic3r also have all free ware STL programs

7 Reply by pirvan

  • pirvan
  • pirvan
  • Member
  • Offline
  • From: San Francisco
  • Registered: 2013-03-27
  • Posts: 1,797

Re: problem with stl file

Or the file is simply too large to upload.  The server seems to allow files that are less than 5MB.  ANything bigger than that it rejects.

Depending on the file, it may be possible to reduce it by zipping it.  If after zipping it's still to large, then you'll have to use one of the on line storage services.

To print or, 3D print, that is the question...
SD3 printer w/too many mods,  Printrbot Simple Maker Ed.,  FormLabs Form 1+
AnyCubic Photon, Shining 3D EinScan-S & Atlas 3D scanners...
...and too much time on my hands.

8 Reply by fixtl

  • fixtl
  • Newbie
  • Offline
  • Registered: 2015-01-27
  • Posts: 7

Re: problem with stl file

if you still need help, i can run them on some proprietory software in the company I work for. let me know