1 Topic by AZERATE

  • AZERATE
  • AZERATE
  • PRINTiT
  • Offline
  • From: Chicago
  • Registered: 2013-11-28
  • Posts: 2,077

Topic: End gcode help

The way I have my current end commands are such:

G28 X0 Y0  ; home X axis and y axis
G1 Z100 F300 ; lower platform to bottom
M104 S0 ; kill extruder temperature
M140 S0 ; kill bed temperature
M84 ; disable motors

But the extruder slams into the front right M4 bolt if I forget to manually click back on Y, THEN hit home X, THEN hit home Y. Can anyone tell me the proper code I would need to return it to the back right position?

Thanks in advance, and sorry if this is in the wrong place on the forum! smile

Printit Mason and Printit Horizon printers
Multiple SD2s- Bulldog XL, E3D v5/v6/Lite6, Volcano, Hobb Goblin, Titan, .9 motor, Lawsy carriages, direct Y drive, fishing line...the list goes on
Filawinder and Filastruder #1870.....worth every penny!

2 Reply by wardjr

  • wardjr
  • wardjr
  • Moderator
  • Offline
  • From: Minnesota
  • Registered: 2013-06-10
  • Posts: 5,624

Re: End gcode help

I'm not certain but on that board you should be able to leave end code in slic3r empty.  Have you tried that?  I don't have any custom end code and it does exactly what you want when it's done.

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

wardjr's Website

3 Reply by AZERATE

  • AZERATE
  • AZERATE
  • PRINTiT
  • Offline
  • From: Chicago
  • Registered: 2013-11-28
  • Posts: 2,077

Re: End gcode help

It depends on the board??

It goes to back right, but when the bed lowers, thats when the extruder moves to the front.

Printit Mason and Printit Horizon printers
Multiple SD2s- Bulldog XL, E3D v5/v6/Lite6, Volcano, Hobb Goblin, Titan, .9 motor, Lawsy carriages, direct Y drive, fishing line...the list goes on
Filawinder and Filastruder #1870.....worth every penny!

4 Reply by adrian

  • adrian
  • Member
  • Offline
  • From: Canberra, Australia
  • Registered: 2013-01-15
  • Posts: 1,623

Re: End gcode help

check "Park Position" under RH->Printer Settings ; "Print" Tab.
For an SD3, try 195, 195, 50  (this is actually off one of my ords, so ignore the values in the screengrab...)

http://www.soliforum.com/misc.php?action=pun_attachment&item=5178

Post's attachments

park.jpg
park.jpg 90.29 kb, file has never been downloaded. 

You don't have the permssions to download the attachments of this post.

5 Reply by wardjr

  • wardjr
  • wardjr
  • Moderator
  • Offline
  • From: Minnesota
  • Registered: 2013-06-10
  • Posts: 5,624

Re: End gcode help

AZERATE wrote:

It depends on the board??

It goes to back right, but when the bed lowers, thats when the extruder moves to the front.

No it depends because it's my board and when i had it on my printer I never needed anything in the end code.  I don't have anything in the end code for the Rumba either so I just made an assumption that it must be in the firmware.  I would guess Adrian will clarify this for us. smile

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

wardjr's Website

6 Reply by adrian

  • adrian
  • Member
  • Offline
  • From: Canberra, Australia
  • Registered: 2013-01-15
  • Posts: 1,623

Re: End gcode help

Firmware has a home setting, which it uses when you home using the g-code... But the Park position is defined in RH.

If it happens after the bed lowers, its coming from the Park process, which is wholly RH derived (see settings above).

7 Reply by adrian

  • adrian
  • Member
  • Offline
  • From: Canberra, Australia
  • Registered: 2013-01-15
  • Posts: 1,623

Re: End gcode help

oh and make sure RH's home-pos is correct...
http://www.soliforum.com/misc.php?action=pun_attachment&item=5181

Post's attachments

home-pos.jpg
home-pos.jpg 94.33 kb, file has never been downloaded. 

You don't have the permssions to download the attachments of this post.

8 Reply by AZERATE

  • AZERATE
  • AZERATE
  • PRINTiT
  • Offline
  • From: Chicago
  • Registered: 2013-11-28
  • Posts: 2,077

Re: End gcode help

Thanks for the help, adrian!
Busy tonight, but I'm looking forward to fiddle with it over the weekend.

Printit Mason and Printit Horizon printers
Multiple SD2s- Bulldog XL, E3D v5/v6/Lite6, Volcano, Hobb Goblin, Titan, .9 motor, Lawsy carriages, direct Y drive, fishing line...the list goes on
Filawinder and Filastruder #1870.....worth every penny!

9 Reply by Hazer

  • Hazer
  • Hazer
  • Member
  • Offline
  • Registered: 2013-07-19
  • Posts: 478

Re: End gcode help

It can be a bit confusing, especially when you look at firmware stuff too. The firmware actually dictates your homing method, but you need to put the homing method into RH (as adrian showed above) not to control the homing, but so that RH understands where your nozzle is when it completes homing.

The RH printer settings are automatically being added to the slicer gcode, along with the custom gcode in the slicer tab. So you have two ways of controlling the end movement. Either use the park position and checkmark 'goto park after job/kill', or add the manual commands to the slicer tab end-gcode.

Chuck Bittner is a quadriplegic gamer who is petitioning the major console developers to include internal button remapping in all console games. You can help.
Sign Chuck Bittners petition

10 Reply by AZERATE

  • AZERATE
  • AZERATE
  • PRINTiT
  • Offline
  • From: Chicago
  • Registered: 2013-11-28
  • Posts: 2,077

Re: End gcode help

Hazer is correct!!
Under Printer Settings/Printer tab, I somehow had Go To Park After Kill Job checked.
I don't know how or why it happened. hmm
Took me a couple days to work with my printer and tinker. Came on here just to post my success and I ended up having the solution already handed to me. I even felt smart for a minute big_smile

Printit Mason and Printit Horizon printers
Multiple SD2s- Bulldog XL, E3D v5/v6/Lite6, Volcano, Hobb Goblin, Titan, .9 motor, Lawsy carriages, direct Y drive, fishing line...the list goes on
Filawinder and Filastruder #1870.....worth every penny!