1 Topic by Tin Falcon (edited by Tin Falcon 2019-02-09 16:19:05)

  • Tin Falcon
  • Tin Falcon
  • Member
  • Offline
  • From: New Jersey, USA
  • Registered: 2014-08-01
  • Posts: 2,424

Topic: A new low cost bed adhesive

Table sugar: just mix a half teaspoon of sugar in a little water heat in microwave about 5 seconds then apply to glass print bed with 14 sheet of paper towel. I have not tried this so do not shoot the messenger


Soliddoodle 4 stock w glass bed------Folger Tech Prusa 2020 upgraded to and titan /aero extruder mirror bed
FT5 with titan/ E3D Aero------MP mini select w glass bed
MP Utimate maker pro-W bondtech extruder
Marlin/Repetier Host/ Slic3r and Cura

2 Reply by 2n2r5

  • 2n2r5
  • 2n2r5
  • Member
  • Offline
  • From: Frederick, MD
  • Registered: 2013-05-09
  • Posts: 1,208

Re: A new low cost bed adhesive

This worked great until I got hungry. Now my tongue is burnt... Thanks a lot.

SD3 w/ mods:
Glass bed with QU-BD heat pad upgrade, threadless ballscrew w/ 8mm smooth rod, spectra line belt replacement, lawsy MK5 extruder, Lawsy replacement carriage, E3D hotend, Ramps 1.4 w/ reprap discount controller, DRV8825 drivers, 12v 30A PS, Acrylic case, Overkill Y-idlers, Filament alarm, Extruder fan + more.

2n2r5's Website

3 Reply by Tin Falcon (edited by Tin Falcon 2019-02-09 03:34:25)

  • Tin Falcon
  • Tin Falcon
  • Member
  • Offline
  • From: New Jersey, USA
  • Registered: 2014-08-01
  • Posts: 2,424

Re: A new low cost bed adhesive

Not recommended for shops with ant problems LOL
Seriously the vidio is pretty impressive. and it cost very little to try.

Soliddoodle 4 stock w glass bed------Folger Tech Prusa 2020 upgraded to and titan /aero extruder mirror bed
FT5 with titan/ E3D Aero------MP mini select w glass bed
MP Utimate maker pro-W bondtech extruder
Marlin/Repetier Host/ Slic3r and Cura

4 Reply by 2n2r5

  • 2n2r5
  • 2n2r5
  • Member
  • Offline
  • From: Frederick, MD
  • Registered: 2013-05-09
  • Posts: 1,208

Re: A new low cost bed adhesive

Agree, would be worth a shot. I really like aquanet but I will be down for a non-aerosol that goes on super thin.

SD3 w/ mods:
Glass bed with QU-BD heat pad upgrade, threadless ballscrew w/ 8mm smooth rod, spectra line belt replacement, lawsy MK5 extruder, Lawsy replacement carriage, E3D hotend, Ramps 1.4 w/ reprap discount controller, DRV8825 drivers, 12v 30A PS, Acrylic case, Overkill Y-idlers, Filament alarm, Extruder fan + more.

2n2r5's Website

5 Reply by yizhou.he

  • yizhou.he
  • yizhou.he
  • Member
  • Offline
  • From: Boston, MA
  • Registered: 2017-07-05
  • Posts: 1,358

Re: A new low cost bed adhesive

this is very old discovery. people also use jello power on heated bed. You might want to wash every print carefully, otherwise the ant issue may not limited to the printer area.

(Da Vinci 1.0, Jr. 1.0 RAMPS, miniMaker) X4, (Creality CR-10S, CR-10 mini, Ender-3) X4, Anycubic MEGA X4, Anycubic Chrion X1, ADMILAB Gantry X2 (MonoPrice Maker Select V2, Plus, Ultimate)X4--Select mini X1, Anycubic photon X4, Wanhao duplicate D7 X1.
iNSTONE Inventor Pro X2, CTC Dual X2, ANET-A8, Hictop 3DP-11, Solidoodle Press, FLSUN I3 2017X1