1 Topic by TheNeck

  • TheNeck
  • TheNeck
  • Member
  • Offline
  • Registered: 2014-05-25
  • Posts: 77

Topic: one of my favorite prints as of late, what is your favorite print?

a low poly megaman

i had to print it as big as possible. big_smile

http://soliforum.com/i/?W4O2Ler.jpg

2 Reply by scobo (edited by scobo 2016-03-27 22:23:39)

  • scobo
  • scobo
  • Member
  • Offline
  • From: Scotland - UK
  • Registered: 2014-08-09
  • Posts: 993

Re: one of my favorite prints as of late, what is your favorite print?

Tie fighter advanced in silver pla with black pla wing panels.
My nephew was blown away by it.

http://i882.photobucket.com/albums/ac28/scobodon/20160322_200140_zpsk4f1fdqj.jpg

Davinci 1.0 with repetier firmware & E3D V6 Lite
Anycubic Photon DLP printer, Einscan-S 3D scanner
Simplify3d, 123D Design, Meshmixer
http://www.thingiverse.com/scobo/designs

3 Reply by reznor9

  • reznor9
  • Member
  • Offline
  • Registered: 2015-11-25
  • Posts: 60

Re: one of my favorite prints as of late, what is your favorite print?

My prototype Batman Arkham Origins Gauntlet. Need to make a few tweaks to it and print it again but I'm impressed with it thus far.
https://farm8.staticflickr.com/7724/26804172905_a580460988_z.jpg

4 Reply by viperz28

  • viperz28
  • Member
  • Offline
  • Registered: 2014-05-22
  • Posts: 122

Re: one of my favorite prints as of late, what is your favorite print?

Can you guys add print times and how you did it? i.e. dual filament on a Da Vinci 1.0?

5 Reply by scobo

  • scobo
  • scobo
  • Member
  • Offline
  • From: Scotland - UK
  • Registered: 2014-08-09
  • Posts: 993

Re: one of my favorite prints as of late, what is your favorite print?

Hi viperz, I printed the Tie Fighter in around 6 hours (3 hours per half).
The wing panels were printed seperately then glued on, I uploaded them here ... http://www.thingiverse.com/thing:1051829

Davinci 1.0 with repetier firmware & E3D V6 Lite
Anycubic Photon DLP printer, Einscan-S 3D scanner
Simplify3d, 123D Design, Meshmixer
http://www.thingiverse.com/scobo/designs

6 Reply by Telemachus

  • Telemachus
  • Member
  • Offline
  • From: Riverside, CA
  • Registered: 2016-01-19
  • Posts: 289

Re: one of my favorite prints as of late, what is your favorite print?

I printed your Tie Fighter and panels for my son and his friends... they loved them!

Da Vinci 1.0a.  Repetier 0.92.  E3D V6.  Titan Extruder.  Sllic3r.  Octoprint on Raspberry Pi B+.

7 Reply by scobo

  • scobo
  • scobo
  • Member
  • Offline
  • From: Scotland - UK
  • Registered: 2014-08-09
  • Posts: 993

Re: one of my favorite prints as of late, what is your favorite print?

Telemachus wrote:

I printed your Tie Fighter and panels for my son and his friends... they loved them!

Cheers for that.
Just for the record, I didn't model the Tie Fighter, just the wing panels. wink

Davinci 1.0 with repetier firmware & E3D V6 Lite
Anycubic Photon DLP printer, Einscan-S 3D scanner
Simplify3d, 123D Design, Meshmixer
http://www.thingiverse.com/scobo/designs