401 Reply by bretc (edited by bretc 2016-02-03 01:43:11)

  • bretc
  • Member
  • Offline
  • Registered: 2016-01-31
  • Posts: 11

Re: DaVinci Junior cartridge reset

janj_fr wrote:
bretc wrote:

Alright so i got my analyzer and nfc shield ordered off of amazon. Should be coming thursday. One i get them do i have to connect the pins on the nfc board (2, 5, 6) to any specific ports on my analyzer or just anything also for the analyzer do i use salae software

Yes that's it. Everything is describe in detail in post above by crcasey and other member.

Do you use the saleae software with that analyzer?

402 Reply by vienisas

  • vienisas
  • Member
  • Offline
  • Registered: 2015-12-16
  • Posts: 60

Re: DaVinci Junior cartridge reset

I have Saleae analyzer 4 and using them software. When you start program need select I2C analyzer and in I2C settings select Hex. Connect ground to pin 2, channel 0  to pin 5 and channel 1 to pin 6. Select record 10 sec. press Star and turn on printer. Its all.

403 Reply by bretc

  • bretc
  • Member
  • Offline
  • Registered: 2016-01-31
  • Posts: 11

Re: DaVinci Junior cartridge reset

vienisas wrote:

I have Saleae analyzer 4 and using them software. When you start program need select I2C analyzer and in I2C settings select Hex. Connect ground to pin 2, channel 0  to pin 5 and channel 1 to pin 6. Select record 10 sec. press Star and turn on printer. Its all.

Ok! I will post my results as soon as I recieve my analyzer and shield on thursday

404 Reply by sangha2006 (edited by sangha2006 2016-02-03 20:48:51)

  • sangha2006
  • Newbie
  • Offline
  • Registered: 2016-01-03
  • Posts: 6

Re: DaVinci Junior cartridge reset

Maybe there is an other way,there is an optical count device on the bowden extruder.
http://soliforum.com/i/?BU1M2bB.jpg
http://soliforum.com/i/?KGQZdAh.jpg

I dont know if it's a good way, but maybe.

405 Reply by jakecrowley

  • jakecrowley
  • Member
  • Offline
  • Registered: 2016-01-02
  • Posts: 85

Re: DaVinci Junior cartridge reset

sangha2006 wrote:

Maybe there is an other way,there is an optical count device on the bowden extruder.
http://soliforum.com/i/?BU1M2bB.jpg
http://soliforum.com/i/?KGQZdAh.jpg

I dont know if it's a good way, but maybe.

I have seen that. I tried to disconnect the connector from the optical sensor board but it still subtracted from the chip. Your best bet right now is to buy a cheap logic analyzer and an nfc shield and an arduino if you don't already have one.

406 Reply by carl_m1968 (edited by carl_m1968 2016-02-03 23:04:11)

  • carl_m1968
  • carl_m1968
  • Member
  • Offline
  • From: Far North almost not Dallas
  • Registered: 2014-10-17
  • Posts: 6,512

Re: DaVinci Junior cartridge reset

jakecrowley wrote:
sangha2006 wrote:

Maybe there is an other way,there is an optical count device on the bowden extruder.
http://soliforum.com/i/?BU1M2bB.jpg
http://soliforum.com/i/?KGQZdAh.jpg

I dont know if it's a good way, but maybe.

I have seen that. I tried to disconnect the connector from the optical sensor board but it still subtracted from the chip. Your best bet right now is to buy a cheap logic analyzer and an nfc shield and an arduino if you don't already have one.


That is a jam and filament out detector. If there is a jam and the feed stops the wheel will stop turning and no longer generate a pulse. If the filament runs out the same will happen.

Printing since 2009 and still love it!
Anycubic 4MAX best $225 ever invested.
Voxelabs Proxima SLA. 6 inch 2k Mono LCD.
Anycubic Predator, massive Delta machine. 450 x 370 print envelope.

407 Reply by jakecrowley

  • jakecrowley
  • Member
  • Offline
  • Registered: 2016-01-02
  • Posts: 85

Re: DaVinci Junior cartridge reset

Just a little note to anyone wondering. I've been using MakerBot PLA just fine after I ordered two spools with the printer not realizing about the DRM. Prints have been coming out excellent. I am using the preset 210C from the chip in the White XYZPrinting spool. I tried it with 190C from the Nature chip that came with the printer and is not getting hot enough to melt the filament. There is a workaround to this by decrypting the 3w file and changing the temperature in the gcode but that is quite annoying to have to do every time you print.

408 Reply by carl_m1968

  • carl_m1968
  • carl_m1968
  • Member
  • Offline
  • From: Far North almost not Dallas
  • Registered: 2014-10-17
  • Posts: 6,512

Re: DaVinci Junior cartridge reset

jakecrowley wrote:

Just a little note to anyone wondering. I've been using MakerBot PLA just fine after I ordered two spools with the printer not realizing about the DRM. Prints have been coming out excellent. I am using the preset 210C from the chip in the White XYZPrinting spool. I tried it with 190C from the Nature chip that came with the printer and is not getting hot enough to melt the filament. There is a workaround to this by decrypting the 3w file and changing the temperature in the gcode but that is quite annoying to have to do every time you print.


Temp will change for every roll and every batch. you just got lucky and found a roll and temp on chip combo that works for now...

Temps from roll to roll can vary as much as 30 degrees. But if you have a 190 chip and a 210 chip you got most of the range covered..

Printing since 2009 and still love it!
Anycubic 4MAX best $225 ever invested.
Voxelabs Proxima SLA. 6 inch 2k Mono LCD.
Anycubic Predator, massive Delta machine. 450 x 370 print envelope.

409 Reply by jakecrowley

  • jakecrowley
  • Member
  • Offline
  • Registered: 2016-01-02
  • Posts: 85

Re: DaVinci Junior cartridge reset

carl_m1968 wrote:
jakecrowley wrote:

Just a little note to anyone wondering. I've been using MakerBot PLA just fine after I ordered two spools with the printer not realizing about the DRM. Prints have been coming out excellent. I am using the preset 210C from the chip in the White XYZPrinting spool. I tried it with 190C from the Nature chip that came with the printer and is not getting hot enough to melt the filament. There is a workaround to this by decrypting the 3w file and changing the temperature in the gcode but that is quite annoying to have to do every time you print.


Temp will change for every roll and every batch. you just got lucky and found a roll and temp on chip combo that works for now...

Temps from roll to roll can vary as much as 30 degrees. But if you have a 190 chip and a 210 chip you got most of the range covered..

The Natural roll that comes with the printer is 190C, so everyone should have this. I also purchased a white spool which is 210C, which hopefully is complient with most spools. I can always just change the temp in the gcode if worse comes to worse.

410 Reply by jakecrowley (edited by jakecrowley 2016-02-04 00:36:21)

  • jakecrowley
  • Member
  • Offline
  • Registered: 2016-01-02
  • Posts: 85

Re: DaVinci Junior cartridge reset

I wonder if this can print ABS. I've seen the Fabrikator Mini print ABS perfectly fine so why cant the jr? I'll have to test out if the extruder can get up to 230C which is the temp cura recommends. If so, I'd be happy to pick some up and test it out.

411 Reply by carl_m1968

  • carl_m1968
  • carl_m1968
  • Member
  • Offline
  • From: Far North almost not Dallas
  • Registered: 2014-10-17
  • Posts: 6,512

Re: DaVinci Junior cartridge reset

jakecrowley wrote:

I wonder if this can print ABS. I've seen the Fabrikator Mini print ABS perfectly fine so why cant the jr? I'll have to test out if the extruder can get up to 230C which is the temp cura recommends. If so, I'd be happy to pick some up and test it out.


I don't know if the Jr. has a Teflon insert in the feed tube and hot end but if it does then 230 is dangerous. Teflon out gases at that temp and higher and that gas can cause flue like symptoms. So be careful and consider ventilation.. The printers that can do higher temps don't have the Teflon insert..

Printing since 2009 and still love it!
Anycubic 4MAX best $225 ever invested.
Voxelabs Proxima SLA. 6 inch 2k Mono LCD.
Anycubic Predator, massive Delta machine. 450 x 370 print envelope.

412 Reply by jakecrowley

  • jakecrowley
  • Member
  • Offline
  • Registered: 2016-01-02
  • Posts: 85

Re: DaVinci Junior cartridge reset

How would I find this? I'm pretty sure it doesn't. I opened up the extruder and its just the bowden tube feeding into what looks to be a plastic filament guide then into the hot end.

413 Reply by vienisas

  • vienisas
  • Member
  • Offline
  • Registered: 2015-12-16
  • Posts: 60

Re: DaVinci Junior cartridge reset

Extruder heating to 230 C but no more, I tried to print with XYZ ABS its melting, but do not want stick to a bed and print is looks bad, I think need 250C

414 Reply by jakecrowley

  • jakecrowley
  • Member
  • Offline
  • Registered: 2016-01-02
  • Posts: 85

Re: DaVinci Junior cartridge reset

vienisas wrote:

Extruder heating to 230 C but no more, I tried to print with XYZ ABS its melting, but do not want stick to a bed and print is looks bad, I think need 250C

This happens when you dont have a heated bed, you can fix it by putting glue stick down onto the print bed before printing

415 Reply by bretc (edited by bretc 2016-02-04 22:13:38)

  • bretc
  • Member
  • Offline
  • Registered: 2016-01-31
  • Posts: 11

Re: DaVinci Junior cartridge reset

Alright! I was able to grab the pass and authenticate. This is what i got.

White Spool (198m):
Pass: 0x81 0xA8 0x71 0x8E
Seems to be an NTAG2xx tag (7 byte UID)
PAGE 00: 04 F6 ED 97  .öí—
PAGE 01: 32 B4 42 80  2´B€
PAGE 02: 44 48 00 00  DH..
PAGE 04: 01 03 A0 0C  .. .
PAGE 05: 34 03 00 FE  4..þ
PAGE 08: 5A 50 57 00  ZPW.
PAGE 09: 00 35 41 4D  .5AM
PAGE 12: D2 00 2D 00  Ò.-.
PAGE 13: 54 48 47 42  THGB
PAGE 14: 30 31 37 38  0178
PAGE 21: DB 1A 31 54  Û.1T
PAGE 22: 0D B4 E0 CE  .´àÎ
PAGE 23: A7 FB 4F 76  §ûOv
PAGE 40: 00 00 00 BD  ...½

Natural Spool (0m):
Pass: 0xCF 0xBC 0x8A 0x89
Seems to be an NTAG2xx tag (7 byte UID)
PAGE 00: 04 34 2E 96  .4.–
PAGE 01: 92 A2 40 81  ’¢@�
PAGE 02: F1 48 00 00  ñH..
PAGE 04: 01 03 A0 0C  .. .
PAGE 05: 34 03 00 FE  4..þ
PAGE 08: 5A 50 5A 00  ZPZ.
PAGE 09: 00 35 32 44  .52D
PAGE 10: A0 86 01 00   †..
PAGE 11: A0 86 01 00   †..
PAGE 12: D2 00 2D 00  Ò.-.
PAGE 13: 54 48 47 42  THGB
PAGE 14: 30 32 36 35  0265
PAGE 21: 48 12 32 54  H.2T
PAGE 22: 90 83 E3 CE  �ƒãÎ
PAGE 23: 12 F2 4A 76  .òJv
PAGE 40: 00 00 00 BD  ...½

416 Reply by bretc

  • bretc
  • Member
  • Offline
  • Registered: 2016-01-31
  • Posts: 11

Re: DaVinci Junior cartridge reset

I ran the reset sketch, put in my password, and the put my chip on and it was a 0/100m but now it says 200/200m! Thank you so much for all your hard work put into this. Now i will go buy some new filament.

417 Reply by bretc

  • bretc
  • Member
  • Offline
  • Registered: 2016-01-31
  • Posts: 11

Re: DaVinci Junior cartridge reset

vienisas wrote:

Color and temperature set by code. Temperature can not be changed.

Page 08:
Nature           :  5A 50 5A 00 /   T 191
Green            :  5A 50 50 00 /   T 210
Red               :  5A 50 32 00 /    T 191
White            :  5A 50 57 00 /    T 210
Black/Olivine  :  5A 50 45 00/     T 191

What happens when you try to change it?

418 Reply by vienisas

  • vienisas
  • Member
  • Offline
  • Registered: 2015-12-16
  • Posts: 60

Re: DaVinci Junior cartridge reset

I had nature and green chips and make from them all five colors. It works.

419 Reply by vienisas

  • vienisas
  • Member
  • Offline
  • Registered: 2015-12-16
  • Posts: 60

Re: DaVinci Junior cartridge reset

http://soliforum.com/i/?4CplkMN.jpg
http://soliforum.com/i/?zuPBI3z.jpg

420 Reply by hydronaut

  • hydronaut
  • Member
  • Offline
  • Registered: 2015-12-26
  • Posts: 45

Re: DaVinci Junior cartridge reset

bretc wrote:
vienisas wrote:

Color and temperature set by code. Temperature can not be changed.

Page 08:
Nature           :  5A 50 5A 00 /   T 191
Green            :  5A 50 50 00 /   T 210
Red               :  5A 50 32 00 /    T 191
White            :  5A 50 57 00 /    T 210
Black/Olivine  :  5A 50 45 00/     T 191

What happens when you try to change it?

Do you mean that the colour controls the temperature?

Also mine always heats up to 205.  Can the temp actually be controlled with the advanced mode and how is everybody monitoring the temperature?

421 Reply by vienisas

  • vienisas
  • Member
  • Offline
  • Registered: 2015-12-16
  • Posts: 60

Re: DaVinci Junior cartridge reset

In the print mode press OK and select MONITOR MODE. Temperature can be change in advance mode before slicing

422 Reply by hydronaut

  • hydronaut
  • Member
  • Offline
  • Registered: 2015-12-26
  • Posts: 45

Re: DaVinci Junior cartridge reset

vienisas wrote:

In the print mode press OK and select MONITOR MODE. Temperature can be change in advance mode before slicing

Thanks, when I press okay in print mode I get print mode cancel and pause only.

423 Reply by vienisas

  • vienisas
  • Member
  • Offline
  • Registered: 2015-12-16
  • Posts: 60

Re: DaVinci Junior cartridge reset

http://soliforum.com/i/?R5u6NyK.jpghttp://soliforum.com/i/?Nz8VExn.jpg

424 Reply by johnnyo1012

  • johnnyo1012
  • Newbie
  • Offline
  • Registered: 2016-02-06
  • Posts: 4

Re: DaVinci Junior cartridge reset

bretc wrote:

I ran the reset sketch, put in my password, and the put my chip on and it was a 0/100m but now it says 200/200m! Thank you so much for all your hard work put into this. Now i will go buy some new filament.

So was a solution found? If so how do I do it?

425 Reply by hydronaut

  • hydronaut
  • Member
  • Offline
  • Registered: 2015-12-26
  • Posts: 45

Re: DaVinci Junior cartridge reset

vienisas wrote:

http://soliforum.com/i/?R5u6NyK.jpghttp://soliforum.com/i/?Nz8VExn.jpg

Mine says cancel where yours says monitor. Firmware version maybe?  I will try upgrading.