1 Topic by Mads_hg (edited by Mads_hg 2015-11-29 15:43:53)

  • Mads_hg
  • Newbie
  • Offline
  • Registered: 2015-11-27
  • Posts: 1

Topic: Issue with Slic3r and stock Da Vinci 1.0a

Hello guys!

I hope you can help me with my issue.

I have tried slicing with Slic3r and afterwards adding the following lines to the gcode-file (before base64-encoding and renaming to a 3w-file, and then sending it to the printer via XYZware):

; filename = composition.3w
; machine = daVinciF10
; material = default
; layer_height = 0.2
; fill_density = 0.10
; shells = 3
; speed = 60
; total_layers = 124
; total_filament = 2116.02
; dimension = 51.23:45.21:24.95
; extruder = 1

And normally the result is perfect. But when I try to print with a lower bed temp (when using PLA), the printer starts heating (as it should) and when the nozzle and bed temp has been reached, the printer head stars the "cleaning" cycle, moves to the heat bed, waits two seconds, and then returns to the starting position (above the drip tray). And there it stands for about 15 min. before it again moves to the heat bed and starts printing.

Do you guys have any clue why the printer just stays there for 15 min. before actually starting to print? I think it's a bit odd, since the the right temps have already been reached.....

Btw. I have flashed the cartridge with 200 degrees nozzle temp and 40 degrees heat bed temp.

I have attached a copy of the gcode and my Slic3r configurations.

My firmware is 1.0.1 and XYZware is version 1.4.1 (Mac).

Thanks!

/Mads

Post's attachments

config.ini 4.15 kb, 5 downloads since 2015-11-29 

gcode.gcode 1.71 mb, 1 downloads since 2015-11-29 

You don't have the permssions to download the attachments of this post.

2 Reply by Teamfox201

  • Teamfox201
  • Newbie
  • Offline
  • Registered: 2015-12-07
  • Posts: 2

Re: Issue with Slic3r and stock Da Vinci 1.0a

Where did you get the start_gcode and end_gcode? This is all my Da Vinci 1.0a config shows...

start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n

end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n

3 Reply by carl_m1968

  • carl_m1968
  • carl_m1968
  • Member
  • Offline
  • From: Far North almost not Dallas
  • Registered: 2014-10-17
  • Posts: 6,512

Re: Issue with Slic3r and stock Da Vinci 1.0a

Teamfox201 wrote:

Where did you get the start_gcode and end_gcode? This is all my Da Vinci 1.0a config shows...

start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n

end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n

You must be using Simplify3D.

Printing since 2009 and still love it!
Anycubic 4MAX best $225 ever invested.
Voxelabs Proxima SLA. 6 inch 2k Mono LCD.
Anycubic Predator, massive Delta machine. 450 x 370 print envelope.

4 Reply by greg_tipton

  • greg_tipton
  • Newbie
  • Offline
  • Registered: 2015-12-08
  • Posts: 1

Re: Issue with Slic3r and stock Da Vinci 1.0a

I have a new XYZ AiO version 1.1.6. Using Slic3r then modifying the gcode. Then encoding base64 with notepad++. Renaming the file .3w.
When I try and use the .3w file XYZware says Incorrect File Format. Any Ideas??