1 Topic by Leinauer98

  • Leinauer98
  • Member
  • Offline
  • Registered: 2015-11-21
  • Posts: 12

Topic: Flashed Davici have a few weird problems. Help needed!

Hey fourm this is my first post here and i have a few problems i hope yall can help me with..
So i decided i was tired of the next to crap xyzfirmware and decoded to flash my davinco 1.0a with repetier host 0.92. Everything seemed to go smoothly until i tried to print. I added the start & ending gcode through my slicer pronter settings. But when i try to start printing my bed and extruder dont heat up. Thats the first problem.. then for some reason my printer thinks its printing in no mans land. Ive been adjusting my printer shape settings. I think i may of fixed that particular issue but i wont know until i can get my bed and extruder heated..
Also another problem i realized. So i used the lcd on the printer to heat the bed and extruder just to make a test peice to see how well the calibration was. & for some odd reason no filament was being extruded.. looked like the printer was doing a dry run!!
If someone could help my semi noob self out that would be much appreciated!! As im using this printer for my small buisness so i need it up asap!!
Thanks,
God bless

2 Reply by wardjr

  • wardjr
  • wardjr
  • Moderator
  • Offline
  • From: Minnesota
  • Registered: 2013-06-10
  • Posts: 5,624

Re: Flashed Davici have a few weird problems. Help needed!

Triple post, please try and avoid that in the future.

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

wardjr's Website

3 Reply by Leinauer98

  • Leinauer98
  • Member
  • Offline
  • Registered: 2015-11-21
  • Posts: 12

Re: Flashed Davici have a few weird problems. Help needed!

wardjr wrote:

Triple post, please try and avoid that in the future.

Yes, my apologies. I didn't recognize that their was an XYZ Printing DaVinci section.

4 Reply by evanalmighty

  • evanalmighty
  • Member
  • Offline
  • Registered: 2015-01-04
  • Posts: 224

Re: Flashed Davici have a few weird problems. Help needed!

You should post your start and end code to see if there's any error there. You also need to level the bed again, manually, after you flash.

5 Reply by wardjr

  • wardjr
  • wardjr
  • Moderator
  • Offline
  • From: Minnesota
  • Registered: 2013-06-10
  • Posts: 5,624

Re: Flashed Davici have a few weird problems. Help needed!

Leinauer98 wrote:
wardjr wrote:

Triple post, please try and avoid that in the future.

Yes, my apologies. I didn't recognize that their was an XYZ Printing DaVinci section.

We are all here to help, I am not very familiar with your printer so hopefully others will get you the advice you seek.  Welcome to the forum.

FYI: looks as though you reported yourself wink

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

wardjr's Website

6 Reply by Leinauer98 (edited by Leinauer98 2015-11-24 01:07:23)

  • Leinauer98
  • Member
  • Offline
  • Registered: 2015-11-21
  • Posts: 12

Re: Flashed Davici have a few weird problems. Help needed!

evanalmighty wrote:

You should post your start and end code to see if there's any error there. You also need to level the bed again, manually, after you flash.

Okay, so manual and auto leveling has been completed..
Here is me starting G-Code --- IS AN ATTACHED FILE
I also added my ending code, printer size, and connection!

Post's attachments

Screenshot (21).png
Screenshot (21).png 254.41 kb, file has never been downloaded. 

Screenshot (22).png 254.3 kb, file has never been downloaded. 

Screenshot (23).png
Screenshot (23).png 255.58 kb, file has never been downloaded. 

Screenshot (24).png
Screenshot (24).png 256.11 kb, file has never been downloaded. 

You don't have the permssions to download the attachments of this post.

7 Reply by evanalmighty

  • evanalmighty
  • Member
  • Offline
  • Registered: 2015-01-04
  • Posts: 224

Re: Flashed Davici have a few weird problems. Help needed!

Try to slice an object and see what kind of GCODE you're getting.  Start/End codes look ok.

8 Reply by carl_m1968

  • carl_m1968
  • carl_m1968
  • Member
  • Offline
  • From: Far North almost not Dallas
  • Registered: 2014-10-17
  • Posts: 6,512

Re: Flashed Davici have a few weird problems. Help needed!

What settings do you have under the extruder tab in printer settings? I have never see start gcode atleast not for Repetier that did not actually specify a numerical value for the M106 and M109 entries. But maybe the newer version that I dont use is smart enough to get the values from the settings.

Printing since 2009 and still love it!
Anycubic 4MAX best $225 ever invested.
Voxelabs Proxima SLA. 6 inch 2k Mono LCD.
Anycubic Predator, massive Delta machine. 450 x 370 print envelope.