1 Topic by Canelondemadera

  • Canelondemadera
  • Newbie
  • Offline
  • Registered: 2015-10-08
  • Posts: 1

Topic: Davinci 1.0 AIO cartridges

Hello, this is my first post.

I´ve got a friend in the US (im from Argentina, that explain my bad english) and i order him a davinci 1.0 aio .
the problem is that here the original cartridge cost +- $70 bucks so its impossible for me to buy it. i´ve seen lots of youtube videos where people hack the cartridge chip with an arduino.
In this video they hack an davinci 1.0 (NOT AIO)

so my question is, the 1.0 and the 1.0 AIO are the same printer with the difference of one having the laser scan and the other not?

Is this method ok? or i will en with a pile of expencive junk.

Greetings from argentina.

2 Reply by DopeSkrit

  • DopeSkrit
  • DopeSkrit
  • Member
  • Offline
  • Registered: 2015-07-31
  • Posts: 67

Re: Davinci 1.0 AIO cartridges

Canelondemadera wrote:

Hello, this is my first post.

I´ve got a friend in the US (im from Argentina, that explain my bad english) and i order him a davinci 1.0 aio .
the problem is that here the original cartridge cost +- $70 bucks so its impossible for me to buy it. i´ve seen lots of youtube videos where people hack the cartridge chip with an arduino.
In this video they hack an davinci 1.0 (NOT AIO)

so my question is, the 1.0 and the 1.0 AIO are the same printer with the difference of one having the laser scan and the other not?

Is this method ok? or i will en with a pile of expencive junk.

Greetings from argentina.

Reflash to Repetier. You will "lose" the scanner. But you can easily reflash to XYZWare if you need the scanner.(https://www.youtube.com/watch?v=sU5G0EX_Q08)

Da Vinci 1.0A Blue | Codename: FreeVinci | E3D v6 Bowden Custom Carriage | Printing PLA, ABS and PETG using S3D
Fabrikator Mini Orange | Printing PLA using Cura
Only printing with sub 20 Euro filaments.

3 Reply by carl_m1968

  • carl_m1968
  • carl_m1968
  • Member
  • Offline
  • From: Far North almost not Dallas
  • Registered: 2014-10-17
  • Posts: 6,512

Re: Davinci 1.0 AIO cartridges

DopeSkrit wrote:
Canelondemadera wrote:

Hello, this is my first post.

I´ve got a friend in the US (im from Argentina, that explain my bad english) and i order him a davinci 1.0 aio .
the problem is that here the original cartridge cost +- $70 bucks so its impossible for me to buy it. i´ve seen lots of youtube videos where people hack the cartridge chip with an arduino.
In this video they hack an davinci 1.0 (NOT AIO)

so my question is, the 1.0 and the 1.0 AIO are the same printer with the difference of one having the laser scan and the other not?

Is this method ok? or i will en with a pile of expencive junk.

Greetings from argentina.

Reflash to Repetier. You will "lose" the scanner. But you can easily reflash to XYZWare if you need the scanner.(https://www.youtube.com/watch?v=sU5G0EX_Q08)

Not really a loss as the scanner on the AIO is useless for the most part.

Printing since 2009 and still love it!
Anycubic 4MAX best $225 ever invested.
Voxelabs Proxima SLA. 6 inch 2k Mono LCD.
Anycubic Predator, massive Delta machine. 450 x 370 print envelope.

4 Reply by kev0175

  • kev0175
  • Member
  • Offline
  • Registered: 2015-02-17
  • Posts: 146

Re: Davinci 1.0 AIO cartridges

If I'm not mistaken I think cartridge resetter works with the current firmware or I could be wrong.

Da Vinci  AiO with firmware 1.1.1 using xyzscan 1.1.18
E3Dv6 hotend with custom carriage with Borosilicate glass bed
123D Design and Simplify3D, Replaced PS with a Solidgear Flex320
Zerokart resetter,  Installed a Extruder Controller for higher temps

5 Reply by DopeSkrit (edited by DopeSkrit 2015-10-09 17:26:13)

  • DopeSkrit
  • DopeSkrit
  • Member
  • Offline
  • Registered: 2015-07-31
  • Posts: 67

Re: Davinci 1.0 AIO cartridges

https://github.com/luc-github/Repetier-Firmware-0.92
https://www.youtube.com/watch?v=rjuCvlnpB7M very good Video. If you need help send me a PM or your Skype ID.

Da Vinci 1.0A Blue | Codename: FreeVinci | E3D v6 Bowden Custom Carriage | Printing PLA, ABS and PETG using S3D
Fabrikator Mini Orange | Printing PLA using Cura
Only printing with sub 20 Euro filaments.