1 Topic by jhabr

  • jhabr
  • Member
  • Offline
  • Registered: 2015-01-16
  • Posts: 18

Topic: Inverted commands a AiO

i'm facing some problems with the ZXY commands at AiO. I don't know if it's a problem since I started to use the Simplify 3D, but when I get the manual commands from the front panel, the right X goes to left... and left goes to right. The Y command up, goes down... and go on.

I don't know if it's the same problem, but I've never could calibrate anymore. The extruder start at back right (home), goes to front right, goes  to front left and it should return at same way to home, but it goes to back left! At this point the extruder cannot continue to home, blocking at left back and at this point, I have to put at home manually with the hands.

Do you guys have any suggestion to it?

2 Reply by carl_m1968 (edited by carl_m1968 2015-08-11 00:05:41)

  • carl_m1968
  • carl_m1968
  • Member
  • Offline
  • From: Far North almost not Dallas
  • Registered: 2014-10-17
  • Posts: 6,512

Re: Inverted commands a AiO

So all you have done is installed simplify3d. You did not flash to repetier? Your machine is 100% stock. But when you use the buttons on the front panel of the machine you get the following.

Press X > the carriage move left and press X < the carriage moves right.

So if you select home all from the machines LCD what happens?

Printing since 2009 and still love it!
Anycubic 4MAX best $225 ever invested.
Voxelabs Proxima SLA. 6 inch 2k Mono LCD.
Anycubic Predator, massive Delta machine. 450 x 370 print envelope.

3 Reply by jhabr

  • jhabr
  • Member
  • Offline
  • Registered: 2015-01-16
  • Posts: 18

Re: Inverted commands a AiO

carl_m1968, you are right at all. When I go home, the bed got inverted and it hangs.

Obs.: When I send a print, everything is right. But the print is bad, because I cannot make a good calibration.

Thanks!

4 Reply by kev0175

  • kev0175
  • Member
  • Offline
  • Registered: 2015-02-17
  • Posts: 146

Re: Inverted commands a AiO

Did you try to do a manual calibration?

Da Vinci  AiO with firmware 1.1.1 using xyzscan 1.1.18
E3Dv6 hotend with custom carriage with Borosilicate glass bed
123D Design and Simplify3D, Replaced PS with a Solidgear Flex320
Zerokart resetter,  Installed a Extruder Controller for higher temps

5 Reply by jhabr

  • jhabr
  • Member
  • Offline
  • Registered: 2015-01-16
  • Posts: 18

Re: Inverted commands a AiO

yes, I've already tried. No success at all, but I really like to understand what happened... hmm

6 Reply by carl_m1968

  • carl_m1968
  • carl_m1968
  • Member
  • Offline
  • From: Far North almost not Dallas
  • Registered: 2014-10-17
  • Posts: 6,512

Re: Inverted commands a AiO

jhabr wrote:

yes, I've already tried. No success at all, but I really like to understand what happened... hmm

There is no way to fail manual calibration. By manual we mean the process that is a sticky in this XYZ section.

You do not use auto calibration ever after using manual. Once you use manual calibration you should be able to print.

Printing since 2009 and still love it!
Anycubic 4MAX best $225 ever invested.
Voxelabs Proxima SLA. 6 inch 2k Mono LCD.
Anycubic Predator, massive Delta machine. 450 x 370 print envelope.