91 Bed Heat Problem
by Ski52
- 2 replies
- 1,652 views
- Last post 2017-03-24 01:10:53 by Ski52
92 Burning Smell
by pakiii
- 1 reply
- 1,383 views
- Last post 2017-03-18 23:45:30 by wardjr
93 Help! Bad hotend connection - Temperature dropping mid-print
by ajflyhigh8
- 10 replies
- 5,241 views
- Last post 2017-03-12 21:27:51 by ajflyhigh8
94 Solidoodle 2 pro with e3d v6 head blockage
by robert.a.downs
- 9 replies
- 5,719 views
- Last post 2017-03-11 15:30:03 by robert.a.downs
95 Thermal runaway
by Revolution289
- 6 replies
- 3,291 views
- Last post 2017-03-07 19:18:19 by heartless
96 Solidoodle 4 Bed Leveling
by my
- 4 replies
- 2,303 views
- Last post 2017-03-01 14:40:10 by heartless
97 Non-constant extrusion issues
by thatcactusgirl
- 4 replies
- 2,871 views
- Last post 2017-02-24 01:38:29 by thatcactusgirl
98 Help! Workbench
by Cadman211
- 15 replies
- 7,453 views
- Last post 2017-02-24 00:14:52 by Uplandstatue
99 could someone slice a file for me
by shields1.as
- 2 replies
- 1,752 views
- Last post 2017-02-19 14:37:55 by heartless
100 After slicing I keep getting this odd post
by shields1.as
- 3 replies
- 2,248 views
- Last post 2017-02-18 22:38:38 by Tin Falcon
101 Fine Tuning My Prints
by Brutalsnowman
- 10 replies
- 5,047 views
- Last post 2017-02-13 12:50:26 by heartless
- 4 replies
- 2,438 views
- Last post 2017-01-21 15:12:43 by heartless
103 CTC 3D Pro Heater Tempeture Read Failure!
by Bassna
- 1 reply
- 1,919 views
- Last post 2017-01-16 09:09:25 by Queb
104 (S4) "active extruder 0" with no power on the board pins
by takadakeyo
- 13 replies
- 8,049 views
- Last post 2017-01-13 19:27:23 by AZERATE
- 14 replies
- 7,591 views
- Last post 2017-01-10 12:05:57 by mmiller7
- 26 replies
- 12,605 views
- Last post 2017-01-05 01:22:41 by Tin Falcon
107 Messed up firmware, software, or settings?
by mmiller7
- 8 replies
- 4,301 views
- Last post 2017-01-02 16:45:47 by wardjr
108 No voltage from extruder on ramps 1.4
by techbuilder2175
- 15 replies
- 18,112 views
- Last post 2016-12-29 03:03:43 by willthiswork89
109 What have I done now?
by Ski52
- 8 replies
- 4,239 views
- Last post 2016-12-25 02:58:52 by Ski52
110 Over Extruding Center of Walls
by lund8619
- 14 replies
- 6,784 views
- Last post 2016-12-23 14:40:53 by lund8619
111 Solidoodle 2 LCD screen keeps rebooting
by yankee5996
- 2 replies
- 2,026 views
- Last post 2016-12-19 00:51:03 by yankee5996
112 solidoodle 2
by Sceubydoo
- 13 replies
- 6,081 views
- Last post 2016-12-18 23:50:44 by wardjr
113 Solidoodle 2 - REV E firmware upgrade
by robert.a.downs
- 3 replies
- 7,241 views
- Last post 2016-12-13 11:07:48 by robert.a.downs
114 "jigsaw" arrived cracked..
by diyengineer
- 12 replies
- 5,204 views
- Last post 2016-12-09 01:07:35 by elmoret
115 Solidoodle 2 pro into rumba marlin firmware
by andysus
- 1 reply
- 1,456 views
- Last post 2016-12-03 14:21:45 by heartless
116 PrintIt - Calidum HALE Heated Bed no longer heating
by Brutalsnowman
- 5 replies
- 3,300 views
- Last post 2016-11-23 12:35:21 by heartless
117 Z axis freezes beginning of print
by themodder4528
- 4 replies
- 2,658 views
- Last post 2016-11-02 08:27:39 by themodder4528
118 Help! AT90USB128DFU not seen as a COM port by Repetier
by VillageEnergyUganda
- 5 replies
- 4,557 views
- Last post 2016-10-31 23:44:54 by OJT
119 Help! Top layer infill holes near perimeter
by Quintox303
- 13 replies
- 29,026 views
- Last post 2016-10-31 06:28:15 by Quintox303
- 121 replies
- 69,814 views
- Last post 2016-10-27 03:10:47 by wardjr