211 New SD2, Stepper motor spazzing out
by bajallama
- 2 replies
- 1,989 views
- Last post 2014-08-04 04:46:36 by bajallama
212 Which controller for homebrew printer?
by pcm81
- 12 replies
- 12,313 views
- Last post 2014-07-31 15:01:15 by IronMan
213 Where to buy parts near LA
by mjd
- 2 replies
- 1,946 views
- Last post 2014-07-17 22:22:56 by elmoret
214 Filament extruder machining required and power supply ?
by Bishoy
- 3 replies
- 2,959 views
- Last post 2014-06-08 11:07:55 by Bishoy
215 RAMPS 1.4 board problems
by davej254
- 2 replies
- 5,180 views
- Last post 2014-06-02 10:43:59 by Hazer
216 extruder motor isolates, does not feed filament
by nltnme_2
- 3 replies
- 2,956 views
- Last post 2014-04-24 03:35:24 by wardjr
217 E3D hotend troubles on solidoodle
by rdoveraven
- 5 replies
- 3,715 views
- Last post 2014-04-22 18:19:18 by rdoveraven
218 BAM&DICE - Arduino based electronics for 3d printing and more
by konmey81
- 0 replies
- 1,726 views
- Last post 2014-04-22 17:09:16 by konmey81
219 D8 (heatbed port) still on 12V
by bikeride
- 1 reply
- 2,166 views
- Last post 2014-04-20 13:28:07 by Hazer
220 DIY with scrap parts from Scanner and Printers
by Serge
- 0 replies
- 2,385 views
- Last post 2014-04-16 23:09:20 by Serge
221 POWER INVERTER
by satman49
- 2 replies
- 2,173 views
- Last post 2014-04-03 10:26:02 by fatpipetelemedicine
222 Nice solidoodle extruder upgrade
by joeyphunk
- 0 replies
- 4,938 views
- Last post 2014-02-23 16:37:34 by joeyphunk
- 2 replies
- 4,220 views
- Last post 2014-02-10 17:38:59 by bnj
224 Upgrading PSU do i keep the barrel connector?
by imanu86
- 10 replies
- 6,642 views
- Last post 2014-01-25 18:28:38 by imanu86
225 maximum input voltage
by satman49
- 1 reply
- 1,666 views
- Last post 2014-01-18 15:52:48 by elmoret
- 3 replies
- 2,992 views
- Last post 2014-01-12 04:15:17 by ITman496
227 stepper motor ,class
by satman49
- 7 replies
- 4,562 views
- Last post 2014-01-11 20:58:14 by satman49
228 Solidoodle Motherboard - SD3 EXP Ports
by pipopoplin
- 1 reply
- 1,703 views
- Last post 2014-01-02 04:38:34 by ronsii
229 3d printer extruder
by 3dprinter
- 1 reply
- 1,671 views
- Last post 2013-12-31 01:29:56 by ronsii
230 Interfacing Force Sensitive Resistor to Printrboard?
by Claghorn
- 2 replies
- 2,909 views
- Last post 2013-12-28 14:06:10 by Claghorn
231 What is the best way to add fans to the circuit board?
by Cyber-Monkey
- 4 replies
- 5,948 views
- Last post 2013-12-16 11:12:21 by Hunter Green
232 RAMPS 1.4.2
by techbuilder2175
- 2 replies
- 3,883 views
- Last post 2013-12-11 01:32:47 by adrian
233 New all metal hotend kickstarter
by dubbsd
- 3 replies
- 2,754 views
- Last post 2013-12-10 05:13:41 by elmoret
234 Looking for connectors for E3D quick change
by Stevos758
- 2 replies
- 2,654 views
- Last post 2013-12-09 19:55:04 by Stevos758
235 Stupid power supply question (at least I hope it is stupid :-).
by Claghorn
- 7 replies
- 7,350 views
- Last post 2013-11-23 06:18:16 by Claghorn
236 Panelolu 2 Upgrade?
by Wavesurf
- 7 replies
- 6,338 views
- Last post 2013-11-19 22:49:24 by caf1182
237 EC3 connectors for power?
by Claghorn
- 0 replies
- 1,728 views
- Last post 2013-11-19 13:50:00 by Claghorn
238 RAMBo mosfets?
by Claghorn
- 1 reply
- 1,913 views
- Last post 2013-11-17 15:33:40 by elmoret
239 NEMA 17 Stepper Motors for 3D Printers
by robotdigg
- 4 replies
- 3,827 views
- Last post 2013-11-17 14:25:25 by fcichock
240 printrboard and vref?
by Claghorn
- 0 replies
- 1,660 views
- Last post 2013-10-30 00:32:58 by Claghorn