<![CDATA[SoliForum - 3D Printing Community — Lost connector to connect xyzprinting da Vinci jr to extruder]]> https://www.soliforum.com/topic/17226/lost-connector-to-connect-xyzprinting-da-vinci-jr-to-extruder/ Wed, 28 Mar 2018 14:02:13 +0000 PunBB <![CDATA[Re: Lost connector to connect xyzprinting da Vinci jr to extruder]]> https://www.soliforum.com/post/143323/#p143323 https://forum.voltivo.com/showthread.php?tid=8517

This is for different board, but the fuse looks similar. There are multiple fuse on the board labeled with R numbers, you can usually tell by the color/appearance if you are experienced. However, it is not easy to replace it for most of people, you are likely to cause more damage if you are not confident on your solder skills.

On the other hand RAMPS Conversion cost more money and you need to read more and learn more skills, but you get printer with better print quality.

Neither of the above is easy, if you are not confident with either of them, sell it for parts on ebay.

]]> Wed, 28 Mar 2018 14:02:13 +0000 https://www.soliforum.com/post/143323/#p143323 <![CDATA[Re: Lost connector to connect xyzprinting da Vinci jr to extruder]]> https://www.soliforum.com/post/143320/#p143320 Where is the fuse on the motherboard?

]]> Wed, 28 Mar 2018 00:37:04 +0000 https://www.soliforum.com/post/143320/#p143320 <![CDATA[Re: Lost connector to connect xyzprinting da Vinci jr to extruder]]> https://www.soliforum.com/post/143306/#p143306 check the fuse on main board then. In the worse case, you can replace the mainboard with RAMPS1.4

http://www.soliforum.com/topic/15273/ho … -ramps-14/

]]> Mon, 26 Mar 2018 23:25:34 +0000 https://www.soliforum.com/post/143306/#p143306 <![CDATA[Re: Lost connector to connect xyzprinting da Vinci jr to extruder]]> https://www.soliforum.com/post/143305/#p143305 No it did not help, the metal piece is disconnected.

]]> Mon, 26 Mar 2018 23:13:06 +0000 https://www.soliforum.com/post/143305/#p143305 <![CDATA[Re: Lost connector to connect xyzprinting da Vinci jr to extruder]]> https://www.soliforum.com/post/143304/#p143304 Will unplug the cable and reboot printer fix it?

Do you have broken metal piece inside of the slot that your cable suppose to insert in?

]]> Mon, 26 Mar 2018 22:51:44 +0000 https://www.soliforum.com/post/143304/#p143304 <![CDATA[Re: Lost connector to connect xyzprinting da Vinci jr to extruder]]> https://www.soliforum.com/post/143303/#p143303 I think I bricked it.
http://soliforum.com/i/?CucoUaW.jpg

]]> Mon, 26 Mar 2018 22:48:54 +0000 https://www.soliforum.com/post/143303/#p143303 <![CDATA[Re: Lost connector to connect xyzprinting da Vinci jr to extruder]]> https://www.soliforum.com/post/143302/#p143302 cut 2mm,dont cut them all. you still have at least 4mm exposed metal contact

]]> Mon, 26 Mar 2018 22:19:41 +0000 https://www.soliforum.com/post/143302/#p143302 <![CDATA[Re: Lost connector to connect xyzprinting da Vinci jr to extruder]]> https://www.soliforum.com/post/143301/#p143301 Even if I was able to do that how would I be able to secure it? Is there a way to 3dprint the metal connector piece, I have another printer.

Thank Tyler

]]> Mon, 26 Mar 2018 22:07:41 +0000 https://www.soliforum.com/post/143301/#p143301 <![CDATA[Re: Lost connector to connect xyzprinting da Vinci jr to extruder]]> https://www.soliforum.com/post/143298/#p143298 If you are not afraid damage it further, cut 2mm from the top so that you can push the cable further in. It's a bad idea, don't try unless you run out of choice. It's one of my beat the dead horse approach. Buy a new cable if possible. Many people RAMPS conversion for their Jr. and don't need the cable anymore. Hopefully they did not throw them away.

]]> Mon, 26 Mar 2018 21:28:03 +0000 https://www.soliforum.com/post/143298/#p143298 <![CDATA[Re: Lost connector to connect xyzprinting da Vinci jr to extruder]]> https://www.soliforum.com/post/143296/#p143296 I don't have the metal part anymore, that the problem.

]]> Mon, 26 Mar 2018 21:12:11 +0000 https://www.soliforum.com/post/143296/#p143296 <![CDATA[Re: Lost connector to connect xyzprinting da Vinci jr to extruder]]> https://www.soliforum.com/post/143294/#p143294 Reshape the metal part and glue it back. Alternatively, ask people that did RAMPS conversion for their Jr. and don't need the cable anymore mail one to you.

]]> Mon, 26 Mar 2018 21:01:44 +0000 https://www.soliforum.com/post/143294/#p143294 <![CDATA[Re: Lost connector to connect xyzprinting da Vinci jr to extruder]]> https://www.soliforum.com/post/143293/#p143293 Sorry, that happen when I post anything from my phone

]]> Mon, 26 Mar 2018 20:51:32 +0000 https://www.soliforum.com/post/143293/#p143293 <![CDATA[Re: Lost connector to connect xyzprinting da Vinci jr to extruder]]> https://www.soliforum.com/post/143291/#p143291 No need to double or triple post.  I deleted the other two.

]]> Mon, 26 Mar 2018 20:37:31 +0000 https://www.soliforum.com/post/143291/#p143291 <![CDATA[Lost connector to connect xyzprinting da Vinci jr to extruder]]> https://www.soliforum.com/post/143290/#p143290 Please help

http://i.imgur.com/p9LwXly.jpg

Thanks Tyler
Tyler@tylertech.in

]]> Mon, 26 Mar 2018 20:31:02 +0000 https://www.soliforum.com/post/143290/#p143290