<![CDATA[SoliForum - 3D Printing Community — Iphone Gear Case Print]]> https://www.soliforum.com/topic/1470/iphone-gear-case-print/ Wed, 27 Feb 2013 13:05:51 +0000 PunBB <![CDATA[Re: Iphone Gear Case Print]]> https://www.soliforum.com/post/14292/#p14292 this for 4s

here is some 5 search thingverse has tons
http://www.thingiverse.com/thing:37542

]]> Wed, 27 Feb 2013 13:05:51 +0000 https://www.soliforum.com/post/14292/#p14292 <![CDATA[Re: Iphone Gear Case Print]]> https://www.soliforum.com/post/14291/#p14291 http://www.thingiverse.com/thing:40190

this one works well. I am gonna tweak it make the walls thicker and some of the openings and try add some flaire to it smile
http://www.thingiverse.com/thing:22572

]]> Wed, 27 Feb 2013 13:04:38 +0000 https://www.soliforum.com/post/14291/#p14291 <![CDATA[Re: Iphone Gear Case Print]]> https://www.soliforum.com/post/14287/#p14287 jj could you post the stl for the case and does it fit the iphone 5

]]> Wed, 27 Feb 2013 10:25:22 +0000 https://www.soliforum.com/post/14287/#p14287 <![CDATA[Re: Iphone Gear Case Print]]> https://www.soliforum.com/post/14172/#p14172 you could just bring the stl into an easy to use 3d package like tinkercad and build your own supports with thing tops to snap them off. I did my first print using kisslicer with support yesterday and it worked pretty well but the bottom of the print has some holes but my print was largely off the bed.

http://distilleryimage5.s3.amazonaws.com/95c423787fc911e28fba22000a1fb1a7_7.jpg

I keep stealing my wife's cricut tools to use on my 3d printer.  The picks that came in this tool set worked great t helping to remove these supports.

http://www.amazon.com/Cricut-7-Piece-To … B0013L9NN0

I'm sure these picks are available for a fraction of the price by some other vendor out there.

]]> Tue, 26 Feb 2013 17:38:06 +0000 https://www.soliforum.com/post/14172/#p14172 <![CDATA[Re: Iphone Gear Case Print]]> https://www.soliforum.com/post/14140/#p14140 SO I wont get a massive solid honeycomb that is more plastic then the total part LOL. It would be nice to select where I want the support. Or delete sections after they are generated.

]]> Tue, 26 Feb 2013 15:18:16 +0000 https://www.soliforum.com/post/14140/#p14140 <![CDATA[Re: Iphone Gear Case Print]]> https://www.soliforum.com/post/14134/#p14134 kisslicer is great at support generation.

general kisslicer settings discussion here.

]]> Tue, 26 Feb 2013 14:27:37 +0000 https://www.soliforum.com/post/14134/#p14134 <![CDATA[Re: Iphone Gear Case Print]]> https://www.soliforum.com/post/14128/#p14128 https://lh6.googleusercontent.com/-pME2DW6EGLI/USy8jE6AaVI/AAAAAAAAAog/DmjLjym1aVU/s747/Photo+Feb+26%2C+7+47+44+AM.jpg

]]> Tue, 26 Feb 2013 13:51:46 +0000 https://www.soliforum.com/post/14128/#p14128 <![CDATA[Re: Iphone Gear Case Print]]> https://www.soliforum.com/post/14127/#p14127 https://lh6.googleusercontent.com/-pME2 … +44+AM.jpg

Well I got it. Flipped it over. 0.3 layer height support on at 2mm Honeycomb and support width was .3 diameter

Overall it printed well but the support was way too thick and broke the sides trying to rip it out.
The top came out much better but I didnt set the back as you can see as solid layer? Maybe I should turn my top layers to 10 so it gets captured as a solid infil.

It worked and there was little to no banding on the walls and minimal blobbing.
The model is a little off probably have to print it 1% bigger and gears 1% smaller.

But question. I could not find support flow rate in slic3r? Only the support width (at .3 ) am I missing something?

]]> Tue, 26 Feb 2013 13:50:31 +0000 https://www.soliforum.com/post/14127/#p14127 <![CDATA[Re: Iphone Gear Case Print]]> https://www.soliforum.com/post/14061/#p14061 I use skeinforge which I hear is better at generating support anyway.  I use either .6 or .7 ratio on my support depending on if it's contacting the bed or not.  Thinnest you can get away with is best.

]]> Mon, 25 Feb 2013 20:28:43 +0000 https://www.soliforum.com/post/14061/#p14061 <![CDATA[Re: Iphone Gear Case Print]]> https://www.soliforum.com/post/14042/#p14042 yes i though of that I figure then I would have 1/2" worth of support but I guess it is easier to break off and wont see it with the case on
\

Mu regular flow rate is .79 my support is it .7? Is that too much? it seemed pretty strong and solid to break off. I used 1.5mm honeycomb I might try a 2mm

]]> Mon, 25 Feb 2013 19:50:55 +0000 https://www.soliforum.com/post/14042/#p14042 <![CDATA[Re: Iphone Gear Case Print]]> https://www.soliforum.com/post/14035/#p14035 Flip the case over and use infill on the inside instead of the outside.  I've printed it before, I think I have a picture up here somewhere.  I never printed the rivets, but I got it working after some sizing of the holes to the posts.

]]> Mon, 25 Feb 2013 19:22:49 +0000 https://www.soliforum.com/post/14035/#p14035 <![CDATA[Iphone Gear Case Print]]> https://www.soliforum.com/post/14030/#p14030 Anyone get this to print well with slicer?

I realized I needed supports then I got it print ok
But:

1: the supports ruin the print trying to break off of the bottom and then they print on the vertical sides that snap onto the phone. Too much support

2: problem is the floor/back/bottom of the case is about 6 layers up from the bed. This allows the gears to rest flush I assume.

I should just start with simplier things like boxes and covers LOL

I used 0.98 slicr
1.5mm honeycomb support
.45 fill
.3 layer height
I turned on solid layers every 1 and infill every 1
top and bottom solids at 3
perimeters was 4
speed around 35mm/s

I was wondering do i just turn the infill off and print the bottom layer as 7 or 8 layers solid? (that way the floor is solid) everything after 10-47 is just the side walls


it printed well looks were OK not great the solid floor still had lots of little misses. Like the infil didn't touch the edges of the model.  The sides came out ok with little to no banding

I think this would be a simpler model and more roboust if it was just one solid piece. Can you print this with gears in place and break them loose?

]]> Mon, 25 Feb 2013 19:01:44 +0000 https://www.soliforum.com/post/14030/#p14030