<![CDATA[SoliForum - 3D Printing Community — Help]]> https://www.soliforum.com/topic/12344/help/ Fri, 25 Sep 2015 19:21:53 +0000 PunBB <![CDATA[Re: Help]]> https://www.soliforum.com/post/106220/#p106220 Thank You so much

]]> Fri, 25 Sep 2015 19:21:53 +0000 https://www.soliforum.com/post/106220/#p106220 <![CDATA[Re: Help]]> https://www.soliforum.com/post/106218/#p106218 Fan connects to the existing fan on the extruder motor, wire it in parallel (red to red, black to black).;

Heater connects to where your heater previously connected.

Thermistor connects to where your thermistor previously connected.

Heater and thermistor are labeled as such on your board, for example in the photo you posted above I can see "E-THERM". That's your extruder thermistor.

]]> Fri, 25 Sep 2015 19:08:18 +0000 https://www.soliforum.com/post/106218/#p106218 <![CDATA[Re: Help]]> https://www.soliforum.com/post/106217/#p106217 Please i need HELP i got my E3D Hotend i follow the instructions from the video and looks good but i don't know where i need to connect the wires the fan and the other two please help i can wait to use it

]]> Fri, 25 Sep 2015 19:00:07 +0000 https://www.soliforum.com/post/106217/#p106217 <![CDATA[Re: Help]]> https://www.soliforum.com/post/105813/#p105813 Thank You

]]> Mon, 21 Sep 2015 01:25:17 +0000 https://www.soliforum.com/post/105813/#p105813 <![CDATA[Re: Help]]> https://www.soliforum.com/post/105812/#p105812 Nope! New hotend consumes the same as old. Ignore any comments about updating your power supply, that's outdated.

]]> Mon, 21 Sep 2015 01:12:51 +0000 https://www.soliforum.com/post/105812/#p105812 <![CDATA[Re: Help]]> https://www.soliforum.com/post/105811/#p105811 Thank You guy's i use the link and use the instructions and i flash it thank you again everyone, another question do i need to upgrade the power supply? yes or no

]]> Mon, 21 Sep 2015 00:56:02 +0000 https://www.soliforum.com/post/105811/#p105811 <![CDATA[Re: Help]]> https://www.soliforum.com/post/105810/#p105810 http://www.soliwiki.com/E3D_extruder#Identify_processor

Use that link for firmware updating and post here if you get stuck.

]]> Mon, 21 Sep 2015 00:50:36 +0000 https://www.soliforum.com/post/105810/#p105810 <![CDATA[Re: Help]]> https://www.soliforum.com/post/105809/#p105809 http://www.soliwiki.com/E3D_extruder is a walkthrough for assembly of the E3D. This was aimed for the v4/v5, so ignore the assembly instructions and follow the Tom's video I linked above. This Soliwiki link gives instructions for flashing the Sang.

The instructions I linked earlier are for the Printrboard only. So please do not follow it for your sake smile

]]> Mon, 21 Sep 2015 00:13:27 +0000 https://www.soliforum.com/post/105809/#p105809 <![CDATA[Re: Help]]> https://www.soliforum.com/post/105808/#p105808 Yes, you have a Sanguinololu, same as me. (I got your email, will reply soon). I'll post a guide to flashing a Sang once I get to a computer.

]]> Mon, 21 Sep 2015 00:09:56 +0000 https://www.soliforum.com/post/105808/#p105808 <![CDATA[Re: Help]]> https://www.soliforum.com/post/105807/#p105807 wow thank you guy's for the help i gonna order my E3D HotEnd right now, to be sure the tutorial is for ether board right the Sanguinololus and Printrboard

]]> Mon, 21 Sep 2015 00:02:40 +0000 https://www.soliforum.com/post/105807/#p105807 <![CDATA[Re: Help]]> https://www.soliforum.com/post/105806/#p105806 Thank You so much i think this one is a Sanguinololus right http://soliforum.com/i/?qLvsssM.jpg

]]> Sun, 20 Sep 2015 23:49:51 +0000 https://www.soliforum.com/post/105806/#p105806 <![CDATA[Re: Help]]> https://www.soliforum.com/post/105805/#p105805 Now that I have a few moments, I dug up an old post I make on another thread.

AZERATE wrote:

Flashing the firmware will be a slightly different process depending on which board you have:
This is a Printrboard
http://i.imgur.com/i0LxV8t.jpg
This is a Sanguinololu
http://i.imgur.com/lypc38S.jpg

This link will give you all steps needed if you have a Printrboard.
I have never needed to flash a Sang, so maybe another user can assist you with that, but the changes in the firmware in the given link are the same no matter the board.
Hope this helps a bit smile

]]> Sun, 20 Sep 2015 23:45:39 +0000 https://www.soliforum.com/post/105805/#p105805 <![CDATA[Re: Help]]> https://www.soliforum.com/post/105804/#p105804 Printrboards are labeled as such on the board. Sanguinololus have a big chip the size of a stick of gum.

]]> Sun, 20 Sep 2015 23:37:23 +0000 https://www.soliforum.com/post/105804/#p105804 <![CDATA[Re: Help]]> https://www.soliforum.com/post/105803/#p105803 Thank You How i can check the board  the i have is anyway to find out

]]> Sun, 20 Sep 2015 23:33:20 +0000 https://www.soliforum.com/post/105803/#p105803 <![CDATA[Re: Help]]> https://www.soliforum.com/post/105802/#p105802 http://www.soliforum.com/topic/7917/e3d … intrboard/

This is for the Printrboard. It is crucial to be sure which board you have. If it is a stock board, the SD2 either has a Sanguinololou or a Printrboard. The given link is not recommended for the Sang.

]]> Sun, 20 Sep 2015 23:19:16 +0000 https://www.soliforum.com/post/105802/#p105802