SoliForum - 3D Printing Community — KISSlicer

Re: KISSlicer

2015-09-14T06:35:01Z

Here are my settings(PLA anyhow for now):

Re: KISSlicer

2015-08-03T15:09:41Z

This is a great slicer. I recommend getting it.

Re: KISSlicer

2015-03-16T16:29:06Z

the 1.5 beta 2.20 is out..
(click on the dropbox link in the first message : http://www.kisslicertalk.com/viewtopic. … &t=362 )

last unofficial english manual here : http://3ntr.eu/wp-content/uploads/2015/ … 080215.pdf

Changes from 2.16:

Arbitrary Z-gap is now allowed
Fixed a bug where the wipe and destring following support interface paths where at the wrong height when Z-Gap was used.
G-code summary at the end now includes per-extruder filament length (and volume) used.
Optimized object slicing with many small sub-meshes.
You can now add up to 5 layers of support interface on top of the raft.
Pressing delete anywhere in the model tab no longer deletes the model.
Fixed a bug where the animation slider would reset itself every second.
Fixed bug when Slice-and-Save is checked and we cancel the file selection.
Every-N-Layers now doesn't drag-value-change.
Added a squiggle-base to the prime pillar to help it adhere to the bed / raft.

Re: KISSlicer

2014-07-08T19:45:45Z

seagel007 wrote:

When I import my Kisslicer g-code into Repetier Host, it shows up about 100 mm off the virtual printbed. Any ideas on how to fix this?

you need to adjust your offset in settings.

Re: KISSlicer

2014-07-07T21:30:55Z

When I import my Kisslicer g-code into Repetier Host, it shows up about 100 mm off the virtual printbed. Any ideas on how to fix this?

Re: KISSlicer

2014-04-25T17:02:35Z

http://www.soliforum.com/topic/6257/kis … -machines/

Re: KISSlicer

2014-02-26T19:30:21Z

Try slowing down you infill speeds under printer/speeds, or you can try printing at a slightly higher temperature.

Re: KISSlicer

2014-02-19T10:23:34Z

So I've been using Kisslicer for a while now, and boy does it slice fast compared to Slic3r, but I can't seem to get great prints below 0.3mm layer height. 0.3mm prints are fantastic and the support is easy to remove.
The issue I have is thin broken infill, and thin fluffy support material that gets dislodged and moved around everywhere. This issue is for both my 0.2mm settings, and 0.1mm settings. I've based my set-up on settings I have found here.
The perimeters seem to come out perfectly though, which is weird.

Has anyone else had that issue? How do I fix it?

Re: KISSlicer

2014-01-30T02:50:36Z

Thanks exactly what I was trying to find.

Re: KISSlicer

2014-01-29T18:57:21Z

Here is a link, the gcode you mention are just for setting mm/in.s and relative pos.

http://reprap.org/wiki/G-code

also here is a link to a thread about starter gcode ---> http://www.soliforum.com/topic/231/impr … end-gcode/

Re: KISSlicer

2014-01-29T16:44:06Z

I have an SD3 and have been using KISSlicer for 6 months and all of a sudden I sliced an object and when I went to save it I got a message that there was no G20 or G91 code at the beginning. When I ran it the bed didn't come up but it just started extruding. It's been so long since I set it up I don't remember what the best initial G codes where for the SD3. Can someone point me in the right direction
Thanks

Re: KISSlicer

2013-11-25T15:49:48Z

aBurtontree wrote:

Hey everyone,
i have the same problem as " ryan-mm85". (
it travels to the lower left corner and dosnt want to stop.
)
I recently received a solidoodle 3 but was not happy with the printing quality at all, so I wanted to try "kisslicer" instead of Slic3er.
Can you help me?

Try reading through this thread... mostly the last pages.

http://www.soliforum.com/topic/4503/suport-material/

Re: KISSlicer

2013-11-25T11:03:45Z

Hey everyone,
i have the same problem as " ryan-mm85". (

it travels to the lower left corner and dosnt want to stop.

)
I recently received a solidoodle 3 but was not happy with the printing quality at all, so I wanted to try "kisslicer" instead of Slic3er.

Can you help me?

Re: KISSlicer

2013-11-11T03:49:06Z

im having issues with the extruder traveling "if you look from the top down into the solidoodle 3" it travels to the lower left corner and dosnt want to stop.

what should I do,
im having trouble understanding this stuff.
can anyone simplify this for me, since I have no clue what the g-code is telling me.

thankyou in advance
Ryan M.

Re: KISSlicer

2013-08-31T21:54:35Z

Thanks for posting the settings! Been returning here several times after fiddling with settings. Just today I managed to set destring suck to 10mm, which resulted in nozzle cleaning and such. All good now. Seems the nozzle was almost clogged after all.

Thanks again!