SoliForum - 3D Printing Community — How de i get the header file from a .3w

Re: How de i get the header file from a .3w

2018-06-08T01:38:34Z

ok, so i tried your program out. exact same output as threedubber. I have brought this to xyz's attention that the settings i set in xyzware are not exporting correctly. my retract speed is set to 30mm/s, on the header file in the gcode from you and threedubber, both say 15mm/s. So something is strange that it is cutting it in half. If i set to 50, header reads 25, if i set to 32, header reads 16. i have tested 4 times with different values haha.
what say you?
Thanks

; filename = Task.3w
; print_time = 3229
; print_time = 4669
; machine = daVinciJR10
; facets = 2524
; total_layers = 21
; version = 18032311
; total_filament = 4683.03
; nozzle_diameter = 0.40
; layer_height = 0.30
; support_material = 0
; support_material_extruder = 1
; extruder_filament = 4683.03:0.00
; extruder = 1
; filamentid = 50,50,
; materialid = 0,
; fill_density = 0.20
; raft_layers = 0
; support_density = 0.15
; shells = 2
; speed = 35.000
; brim_width = 0.000
; dimension = 76.55:107.95:6.35
; fill_pattern = rectilinear
; perimeter_speed = 15.000
; small_perimeter_speed = 10.000
; bridge_speed = 10.000
; travel_speed = 100.000
; retract_speed = 15
; retract_length = 4.000
; first_layer_speed = 5.000

Re: How de i get the header file from a .3w

2018-06-08T00:56:46Z

Omg, sorry for such a late reply. Never recieved a notification about this. Ok, ill grab your program. I contacted xyz and asked what standard speed was and the tech wasnt sure.

So i am only wanting to see header info so that i can see what settings are what haha

Thanks

Re: How de i get the header file from a .3w

2018-06-03T00:53:25Z

I think threedubber monkeys with the header even when decrypting the file. You can use my program to decrypt the file, I leave the header alone when decrypting and only make minimal changes when encrypting.

http://www.soliforum.com/topic/17028/pr … minimaker/

Re: How de i get the header file from a .3w

2018-05-25T17:56:08Z

Ok, i found threedubber but now i have some questions. It looks as if my software is not using the settings i tell it to. For example, here is what i told xyz ware to do

Quality: normal(this is the lowest one i have to choose. its either normal, good or best)
Speed:fast(selected by default and according to release notes, its 100mm/s)
infil:10%
shells: normal
Larer height: 0.4
temp:215C
retract speed = 30mm/s
retract length 4mm

Ok, so now i export it from xyzware, i do not use anything else, just xyzware.

decrypt in threedub and here is the output, notice the speedand retract speeds are not what i exported them as in the .3w file

; filename = Task.3w
; print_time = 1792
; print_time = 2461
; machine = daVinciJR10
; facets = 2468
; total_layers = 42
; version = 18032311
; total_filament = 3338.23
; nozzle_diameter = 0.40
; layer_height = 0.40
; support_material = 0
; support_material_extruder = 1
; extruder_filament = 3338.23:0.00
; extruder = 1
; filamentid = 50,50,
; materialid = 0,
; fill_density = 0.10
; raft_layers = 0
; support_density = 0.15
; shells = 2
; speed = 40.000
; brim_width = 0.000
; dimension = 44.22:44.22:16.75
; fill_pattern = rectilinear
; perimeter_speed = 30.000
; small_perimeter_speed = 10.000
; bridge_speed = 10.000
; retract_speed = 15
; retract_length = 4.000
; first_layer_speed = 5.000
; Call_From_APP = XYZware 2.1.29.2
; speed_limit_open = 1
; Total computing time = 0.000 sec.
; threads = 1

How de i get the header file from a .3w

2018-05-25T17:27:20Z

Ok, so here is my goal. I am not wanting to use slic3r or cura with my jr 1.0. I happen to like the newest version of xyzware since now i can control retract speed, length and temp with their software.

What i am wanting to do is view the header file of a .3w to see what options it sets when i export from xyzware. IE, speed in the program i set to standard but in the header file it will actually give me a number like 60mm/s or whatever.

Does such a program exist that is easy to use?

thanks

Matt