<![CDATA[SoliForum - 3D Printing Community — Raspberry pi 3?]]> 2017-04-15T13:14:22Z PunBB https://www.soliforum.com/topic/14241/raspberry-pi-3/ <![CDATA[Re: Raspberry pi 3?]]> The following page looks like it describes the problem you are facing.  It shows how to prevent the Pi from taking the WiFi into power save mode.

http://qdosmsq.dunbar-it.co.uk/blog/201 … r-a-while/

- Uriah

]]> https://www.soliforum.com/user/4789/ 2017-04-15T13:14:22Z https://www.soliforum.com/post/134587/#p134587 <![CDATA[Re: Raspberry pi 3?]]> Powering the Pi through the 5V pins with a ample power supply.  I am running the newest Raspbian release.

]]> https://www.soliforum.com/user/11821/ 2017-04-14T15:13:35Z https://www.soliforum.com/post/134552/#p134552 <![CDATA[Re: Raspberry pi 3?]]> Are you using the ATLAS 3D hardware or are you powering the Pi over USB?

]]> https://www.soliforum.com/user/4789/ 2017-04-10T23:59:29Z https://www.soliforum.com/post/134458/#p134458 <![CDATA[Re: Raspberry pi 3?]]> Running FreeLSS on a Pi 3 and I am having the worst issues with Raspbian Pixel and the built-in wifi.  Despite being connected to a wireless network, I am unable to access by SSH or HTTP after a few minutes.  I also noticed that DNS was not behaving either, forcing me to "sudo dhclient -v wlan0".  If I go wired, it is not a problem (except for the later DNS issue).  I did read that the issue is due to IPv4 vs IPv6 being enabled 

I updated the firmware on the Pi and made sure that low power mode is disabled but no go.  If I go with the edimax I do not have any problem and can leave the scanner on for hours.

Has anyone encountered this problem ?

I also had issues running make autostart so I had to revert to running from a command line.  I read in the forum that this is a permissions error in the ./desktop folder.   Is there a straigtforward solution to this as well ?

]]> https://www.soliforum.com/user/11821/ 2017-04-06T19:09:28Z https://www.soliforum.com/post/134357/#p134357 <![CDATA[Re: Raspberry pi 3?]]> HI. Can someone give fact how much quicker pi3 is?
Are it's any idea to upgrade pi2/old model camera  to pi3/v2. Camera?  I have licensed version of software and heavy-duty aluminum scanner frame. I have also thinking to change those red laser to better green or blue but are this help anything?

]]> https://www.soliforum.com/user/16127/ 2017-02-05T13:03:47Z https://www.soliforum.com/post/132086/#p132086 <![CDATA[Re: Raspberry pi 3?]]> I have began testing with the Raspberry Pi 3 and the results look great so far.  Unfortunately it's not compatible with the SD image for the Pi 2 and B+ so the upgrade isn't as simple as just plugging your current ATLAS 3D card into the Pi 3.  I'll keep you posted.

- Uriah

]]> https://www.soliforum.com/user/4789/ 2016-03-28T23:10:28Z https://www.soliforum.com/post/120106/#p120106 <![CDATA[Re: Raspberry pi 3?]]> After seeing this post, and having ordered the kit I thought this would be a good challenge - and I have sort of succeeded in the task!

See my post on the challenges, but seems to be working well at the moment smile

http://www.soliforum.com/topic/14371/up … i-3-build/

Regards,

Andy

]]> https://www.soliforum.com/user/13910/ 2016-03-26T19:10:25Z https://www.soliforum.com/post/119980/#p119980 <![CDATA[Re: Raspberry pi 3?]]> at least no WIFI driver issues since built in

]]> https://www.soliforum.com/user/795/ 2016-03-08T06:06:04Z https://www.soliforum.com/post/118897/#p118897 <![CDATA[Re: Raspberry pi 3?]]> It should be faster.  I'm still trying to get my hands on one to test.

]]> https://www.soliforum.com/user/4789/ 2016-03-08T01:44:19Z https://www.soliforum.com/post/118880/#p118880 <![CDATA[Raspberry pi 3?]]> So who's going to be the first person to see how well freelss runs on the new raspberry pi 3? It should theoretically be faster, right?

]]> https://www.soliforum.com/user/10162/ 2016-03-07T21:49:35Z https://www.soliforum.com/post/118867/#p118867