<![CDATA[SoliForum - 3D Printing Community — Help]]> 2015-09-25T19:21:53Z PunBB https://www.soliforum.com/topic/12344/help/ <![CDATA[Re: Help]]> Thank You so much

]]> https://www.soliforum.com/user/3012/ 2015-09-25T19:21:53Z https://www.soliforum.com/post/106220/#p106220 <![CDATA[Re: Help]]> Fan connects to the existing fan on the extruder motor, wire it in parallel (red to red, black to black).;

Heater connects to where your heater previously connected.

Thermistor connects to where your thermistor previously connected.

Heater and thermistor are labeled as such on your board, for example in the photo you posted above I can see "E-THERM". That's your extruder thermistor.

]]> https://www.soliforum.com/user/221/ 2015-09-25T19:08:18Z https://www.soliforum.com/post/106218/#p106218 <![CDATA[Re: Help]]> Please i need HELP i got my E3D Hotend i follow the instructions from the video and looks good but i don't know where i need to connect the wires the fan and the other two please help i can wait to use it

]]> https://www.soliforum.com/user/3012/ 2015-09-25T19:00:07Z https://www.soliforum.com/post/106217/#p106217 <![CDATA[Re: Help]]> Thank You

]]> https://www.soliforum.com/user/3012/ 2015-09-21T01:25:17Z https://www.soliforum.com/post/105813/#p105813 <![CDATA[Re: Help]]> Nope! New hotend consumes the same as old. Ignore any comments about updating your power supply, that's outdated.

]]> https://www.soliforum.com/user/221/ 2015-09-21T01:12:51Z https://www.soliforum.com/post/105812/#p105812 <![CDATA[Re: Help]]> Thank You guy's i use the link and use the instructions and i flash it thank you again everyone, another question do i need to upgrade the power supply? yes or no

]]> https://www.soliforum.com/user/3012/ 2015-09-21T00:56:02Z https://www.soliforum.com/post/105811/#p105811 <![CDATA[Re: Help]]> http://www.soliwiki.com/E3D_extruder#Identify_processor

Use that link for firmware updating and post here if you get stuck.

]]> https://www.soliforum.com/user/221/ 2015-09-21T00:50:36Z https://www.soliforum.com/post/105810/#p105810 <![CDATA[Re: Help]]> http://www.soliwiki.com/E3D_extruder is a walkthrough for assembly of the E3D. This was aimed for the v4/v5, so ignore the assembly instructions and follow the Tom's video I linked above. This Soliwiki link gives instructions for flashing the Sang.

The instructions I linked earlier are for the Printrboard only. So please do not follow it for your sake smile

]]> https://www.soliforum.com/user/4188/ 2015-09-21T00:13:27Z https://www.soliforum.com/post/105809/#p105809 <![CDATA[Re: Help]]> Yes, you have a Sanguinololu, same as me. (I got your email, will reply soon). I'll post a guide to flashing a Sang once I get to a computer.

]]> https://www.soliforum.com/user/221/ 2015-09-21T00:09:56Z https://www.soliforum.com/post/105808/#p105808 <![CDATA[Re: Help]]> wow thank you guy's for the help i gonna order my E3D HotEnd right now, to be sure the tutorial is for ether board right the Sanguinololus and Printrboard

]]> https://www.soliforum.com/user/3012/ 2015-09-21T00:02:40Z https://www.soliforum.com/post/105807/#p105807 <![CDATA[Re: Help]]> Thank You so much i think this one is a Sanguinololus right http://soliforum.com/i/?qLvsssM.jpg

]]> https://www.soliforum.com/user/3012/ 2015-09-20T23:49:51Z https://www.soliforum.com/post/105806/#p105806 <![CDATA[Re: Help]]> Now that I have a few moments, I dug up an old post I make on another thread.

AZERATE wrote:

Flashing the firmware will be a slightly different process depending on which board you have:
This is a Printrboard
http://i.imgur.com/i0LxV8t.jpg
This is a Sanguinololu
http://i.imgur.com/lypc38S.jpg

This link will give you all steps needed if you have a Printrboard.
I have never needed to flash a Sang, so maybe another user can assist you with that, but the changes in the firmware in the given link are the same no matter the board.
Hope this helps a bit smile

]]> https://www.soliforum.com/user/4188/ 2015-09-20T23:45:39Z https://www.soliforum.com/post/105805/#p105805 <![CDATA[Re: Help]]> Printrboards are labeled as such on the board. Sanguinololus have a big chip the size of a stick of gum.

]]> https://www.soliforum.com/user/221/ 2015-09-20T23:37:23Z https://www.soliforum.com/post/105804/#p105804 <![CDATA[Re: Help]]> Thank You How i can check the board  the i have is anyway to find out

]]> https://www.soliforum.com/user/3012/ 2015-09-20T23:33:20Z https://www.soliforum.com/post/105803/#p105803 <![CDATA[Re: Help]]> http://www.soliforum.com/topic/7917/e3d … intrboard/

This is for the Printrboard. It is crucial to be sure which board you have. If it is a stock board, the SD2 either has a Sanguinololou or a Printrboard. The given link is not recommended for the Sang.

]]> https://www.soliforum.com/user/4188/ 2015-09-20T23:19:16Z https://www.soliforum.com/post/105802/#p105802