26 Reply by 108emmett (edited by 108emmett 2015-01-18 22:50:52)

  • 108emmett
  • Newbie
  • Offline
  • Registered: 2015-01-18
  • Posts: 4

Re: XYZ Da Vinci Filament Counter Resetter

fr3
Many Many thanks for your efforts and posts. I got one of your resetters which will be put to use soon. I have been wanting to get some advice from someone experienced in this area. Can you recommend to a neophyte what would be the best way or best websites I should use to educate myself as regards programing, arduino, hardware and management of 3D printing. I have absolutely no background in these areas or writing code though I am very motivated now to learn. I don't even know what type of language is being used. What's the best one to learn? I have checked into repetier, slcr 3, etc.. but I haven't found out where I have to go to get a good grounding in the programs. Can you recommend any books or sites?

I put together a TwoUp kit--I made oscilloscopes, etc.. pre-teen-- but I have absolutely no idea how to navigate all the stuff needed to tweek a printer and use the software successfully. I have no history at all with PCs and am at the very beginning of that intimidating bell curve that always pops up with computers. So If you have the inclination and time, any advice would be greatly appreciated.  Many thanks.

27 Reply by wimismith (edited by wimismith 2015-05-21 21:33:00)

  • wimismith
  • Member
  • Offline
  • Registered: 2014-11-09
  • Posts: 44

Re: XYZ Da Vinci Filament Counter Resetter

I'm having a little trouble with making the resetter, I'm using an arduino nano, I think I have it wired correctly, and I've uploaded the recommended program, but I'm sufficiently new at working with arduinos that I'm not sure. The leads have alligator clips running to the housing that has the pins in it. I've uploaded how I have it wired, if I need to I can use an arduino mega that I also have.  http://soliforum.com/i/?0Rl9dDD.jpg

28 Reply by jamerfut

  • jamerfut
  • Member
  • Offline
  • Registered: 2015-05-06
  • Posts: 51

Re: XYZ Da Vinci Filament Counter Resetter

I have placed an order for your pro resetter and asked it to be sent 2 day priority it's been now 4 days and i am still waiting for it tracking says it setting in TX i have sent WCtek message asking for a check on my order with no response.

29 Reply by batmaster

  • batmaster
  • Member
  • Offline
  • Registered: 2015-06-04
  • Posts: 60

Re: XYZ Da Vinci Filament Counter Resetter

I have a davinci 1.0A which i received yesterday and it did its updates(damn).  Am i screwed?  I was going to order one of these but i cannot find any concrete answer as to whether it will work on my machine or not. 

Any guidance appreciated.

30 Reply by carl_m1968

  • carl_m1968
  • carl_m1968
  • Member
  • Offline
  • From: Far North almost not Dallas
  • Registered: 2014-10-17
  • Posts: 6,512

Re: XYZ Da Vinci Filament Counter Resetter

batmaster wrote:

I have a davinci 1.0A which i received yesterday and it did its updates(damn).  Am i screwed?  I was going to order one of these but i cannot find any concrete answer as to whether it will work on my machine or not. 

Any guidance appreciated.

If it wont work just flash the firmware to Repetier .92 and use Repetier Host . Then you can use any brand filaments.

Printing since 2009 and still love it!
Anycubic 4MAX best $225 ever invested.
Voxelabs Proxima SLA. 6 inch 2k Mono LCD.
Anycubic Predator, massive Delta machine. 450 x 370 print envelope.

31 Reply by batmaster

  • batmaster
  • Member
  • Offline
  • Registered: 2015-06-04
  • Posts: 60

Re: XYZ Da Vinci Filament Counter Resetter

carl_m1968 wrote:
batmaster wrote:

I have a davinci 1.0A which i received yesterday and it did its updates(damn).  Am i screwed?  I was going to order one of these but i cannot find any concrete answer as to whether it will work on my machine or not. 

Any guidance appreciated.

If it wont work just flash the firmware to Repetier .92 and use Repetier Host . Then you can use any brand filaments.

Would there happen to be something somewhere that explains this process?  Do you mean if i do this i dont even require the resetter?  is it still as easy to use as the xyzware?

32 Reply by lclark283 (edited by lclark283 2015-06-09 08:39:19)

  • lclark283
  • Newbie
  • Offline
  • Registered: 2015-06-09
  • Posts: 1

Re: XYZ Da Vinci Filament Counter Resetter

This is related to fr333n3rgy  Posts 2014-07-17
Here is what I found after looking around :

Testing connection to Da Vinci EEPROM CHIP

Da Vinci EEPROM found...

Reading the Davinci EEPROM Contents...
(success)

00: 5A414E000034345680A9030080A90300 ZAN..44V........

10: B9000000544847423031313900000000 ....THGB0119....
20: 0000000034000000FFFFFFFFAA55AA55 ....4........U.U
30: 883355AA80A903000000001004ED00E0 .3U.............

40: 5A414E000034345680A9030080A90300 ZAN..44V........
50: B9000000544847423031313900000000 ....THGB0119....

60: 0000000034000000FFFFFFFFAA55AA55 ....4........U.U
70: 883355AA80A90300AA55AA55C7B00A00 .3U......U.U....

Updating EEPROM...
(success)
(success)
(success)

(success)
(success)
(success)

(success)

(success)
(success)
(success)

Dumping Content after modification...
(success)
00: 5A414E000034345680A9030080A90300 ZAN..44V........
10: B9000000544847423031313900000000 ....THGB0119....
20: 0000000034000000FFFFFFFFAA55AA55 ....4........U.U

30: 883355AA80A903000000001004ED00E0 .3U.............
40: 5A414E000034345680A9030080A90300 ZAN..44V........
50: B9000000544847423031313900000000 ....THGB0119....
60: 0000000034000000FFFFFFFFAA55AA55 ....4........U.U
70: 883355AA80A90300AA55AA55C7B00A00 .3U......U.U....

Testing connection to Da Vinci EEPROM CHIP

Da Vinci EEPROM found...
Reading the Davinci EEPROM Contents...
(success)
00: 5A414E000034345680A9030080A90300 ZAN..44V........
10: B9000000544847423031313900000000 ....THGB0119....

20: 0000000034000000FFFFFFFFAA55AA55 ....4........U.U
30: 883355AA80A903000000001004ED00E0 .3U.............
40: 5A414E000034345680A9030080A90300 ZAN..44V........
50: B9000000544847423031313900000000 ....THGB0119....
60: 0000000034000000FFFFFFFFAA55AA55 ....4........U.U
70: 883355AA80A90300AA55AA55C7B00A00 .3U......U.U....
Updating EEPROM...
(success)

(success)
(success)
(success)
(success)
(success)

(success)
(success)
(success)
(success)

Dumping Content after modification...
(success)
00: 5A414E000034345680A9030080A90300 ZAN..44V........
10: B9000000544847423031313900000000 ....THGB0119....

20: 0000000034000000FFFFFFFFAA55AA55 ....4........U.U
30: 883355AA80A903000000001004ED00E0 .3U.............
40: 5A414E000034345680A9030080A90300 ZAN..44V........
50: B9000000544847423031313900000000 ....THGB0119....
60: 0000000034000000FFFFFFFFAA55AA55 ....4........U.U
70: 883355AA80A90300AA55AA55C7B00A00 .3U......U.U....

33 Reply by ahmedsalahnol

  • ahmedsalahnol
  • Newbie
  • Offline
  • Registered: 2015-08-21
  • Posts: 1

Re: XYZ Da Vinci Filament Counter Resetter

hello
it is working very well by rest counter , but temperature did not change as i changed temperature from 210c   to 230c
but maximum temperature read by sensor was 215 c which appear on screen of printer is there any solution ??
thanks for you

34 Reply by Landin81

  • Landin81
  • Landin81
  • Member
  • Offline
  • Registered: 2015-07-24
  • Posts: 66

Re: XYZ Da Vinci Filament Counter Resetter

What settings for printing PLA?
Is there a way to shut the bed temp OFF completly?