26 Reply by thelothar74

  • thelothar74
  • Member
  • Offline
  • Registered: 2017-03-26
  • Posts: 23

Re: Solidoodle 4 Board fried?

Sorry for the delay, for sure I will post info on how it works out. I had a setback with my laptop a few days ago, the hard drive crapped out on me. So it may be a few more days til I'm back to tinkering with my printer.

27 Reply by heartless

  • heartless
  • heartless
  • Member
  • Offline
  • From: Northcentral Wisconsin
  • Registered: 2015-04-08
  • Posts: 2,152

Re: Solidoodle 4 Board fried?

Ugh, sorry to hear about the laptop. that stinks.

Hope you get it sorted out soon.

SD4 #1 & #2 - Lawsy carriages, E3D v6, Rumba controller board, mirror bed plate, X motor fan, upgraded PSU & Mica bed heater
SD4 #3 - in the works ~ Folgertech FT-5, rev 1
Printit Industries Beta Tester - Horizon H1

28 Reply by thelothar74

  • thelothar74
  • Member
  • Offline
  • Registered: 2017-03-26
  • Posts: 23

Re: Solidoodle 4 Board fried?

OK new(used) laptop.Previously I compiled and uploaded firmware) Installed soliprint and virtual driver then repetier host. But nothing works, no lights, no fans. http://soliforum.com/i/?rgvNybx.jpghttp://soliforum.com/i/?NjUhURK.jpghttp://soliforum.com/i/?j6qTbb8.jpg

Any clue what I am doing wrong, or did wrong?

29 Reply by Tin Falcon

  • Tin Falcon
  • Tin Falcon
  • Member
  • Offline
  • From: New Jersey, USA
  • Registered: 2014-08-01
  • Posts: 2,424

Re: Solidoodle 4 Board fried?

Why are you using solid print and repitier host.
The driver should be installed with your  your arduino and then just use repiter to run things.

Soliddoodle 4 stock w glass bed------Folger Tech Prusa 2020 upgraded to and titan /aero extruder mirror bed
FT5 with titan/ E3D Aero------MP mini select w glass bed
MP Utimate maker pro-W bondtech extruder
Marlin/Repetier Host/ Slic3r and Cura

30 Reply by thelothar74 (edited by thelothar74 2017-12-04 23:38:54)

  • thelothar74
  • Member
  • Offline
  • Registered: 2017-03-26
  • Posts: 23

Re: Solidoodle 4 Board fried?

I sort of figured it would run on the old software, since I uploaded the firmware to the mks? So dont use host, just regular repitier?

31 Reply by Tin Falcon

  • Tin Falcon
  • Tin Falcon
  • Member
  • Offline
  • From: New Jersey, USA
  • Registered: 2014-08-01
  • Posts: 2,424

Re: Solidoodle 4 Board fried?

Repetier Host comes with cura and slic3r  so they need to be configured as well.

Soliddoodle 4 stock w glass bed------Folger Tech Prusa 2020 upgraded to and titan /aero extruder mirror bed
FT5 with titan/ E3D Aero------MP mini select w glass bed
MP Utimate maker pro-W bondtech extruder
Marlin/Repetier Host/ Slic3r and Cura

32 Reply by thelothar74

  • thelothar74
  • Member
  • Offline
  • Registered: 2017-03-26
  • Posts: 23

Re: Solidoodle 4 Board fried?

Well after taking alot of time off, Im back to trying to figure things out... So I can manually move x , y , z in Rep, but when I home any of them they go the opposite direction. Any ideas?

33 Reply by wardjr

  • wardjr
  • wardjr
  • Moderator
  • Offline
  • From: Minnesota
  • Registered: 2013-06-10
  • Posts: 5,623

Re: Solidoodle 4 Board fried?

Yep you have endstops that aren’t working. Or you have your printer configuration incorrect within RH.
200,200 is Home on an SD.  That is the right rear of the machine.

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

wardjr's Website

34 Reply by thelothar74

  • thelothar74
  • Member
  • Offline
  • Registered: 2017-03-26
  • Posts: 23

Re: Solidoodle 4 Board fried?

ok, for some reason I thought home was 0,0 at the right rear. I shall redo the config and see if that helps

35 Reply by thelothar74

  • thelothar74
  • Member
  • Offline
  • Registered: 2017-03-26
  • Posts: 23

Re: Solidoodle 4 Board fried?

K, the config in Rep host was at park and home at 200 already, so dont think that is the issue.http://soliforum.com/i/?du69C9J.jpg
But while looking in the sketch config, it lists this. Should it be changed to x home pos 200 and y too?

36 Reply by wardjr

  • wardjr
  • wardjr
  • Moderator
  • Offline
  • From: Minnesota
  • Registered: 2013-06-10
  • Posts: 5,623

Re: Solidoodle 4 Board fried?

What version of Marlin is that?
Probably want this one https://github.com/ozadr1an/Solidoodle- … in_v1_beta

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

wardjr's Website

37 Reply by thelothar74

  • thelothar74
  • Member
  • Offline
  • Registered: 2017-03-26
  • Posts: 23

Re: Solidoodle 4 Board fried?

Not sure, just used the one in the link, even remembered to define the board lol, compiled and uploaded. now end stops are triggered, have to look up what I changed before.