You are not logged in. Please login or register.
SoliForum - 3D Printing Community → XYZ Printing DaVinci → Extruder Stepper Clicking!
I have Da Vinci 1.0 AIO and i have Repetier. My prints all start fine and all the layers look great and I have a great setup.... but while in the middle of my prints the extruder stepper starts clicking like it cant feed the filament, and then stops dispensing filament... i don't know what to do has anyone had this issue...
I have Da Vinci 1.0 AIO and i have Repetier. My prints all start fine and all the layers look great and I have a great setup.... but while in the middle of my prints the extruder stepper starts clicking like it cant feed the filament, and then stops dispensing filament... i don't know what to do has anyone had this issue...
A bad connection on your heater is causing it to cool.
smviens wrote:I have Da Vinci 1.0 AIO and i have Repetier. My prints all start fine and all the layers look great and I have a great setup.... but while in the middle of my prints the extruder stepper starts clicking like it cant feed the filament, and then stops dispensing filament... i don't know what to do has anyone had this issue...
A bad connection on your heater is causing it to cool.
Do you have any suggestions on how to fix this? Should i try and just hard wire the heater... by that i mean cut out the quick connect and put a crimp connection?
carl_m1968 wrote:smviens wrote:I have Da Vinci 1.0 AIO and i have Repetier. My prints all start fine and all the layers look great and I have a great setup.... but while in the middle of my prints the extruder stepper starts clicking like it cant feed the filament, and then stops dispensing filament... i don't know what to do has anyone had this issue...
A bad connection on your heater is causing it to cool.
Do you have any suggestions on how to fix this? Should i try and just hard wire the heater... by that i mean cut out the quick connect and put a crimp connection?
That is most of us have done.
smviens wrote:carl_m1968 wrote:A bad connection on your heater is causing it to cool.
Do you have any suggestions on how to fix this? Should i try and just hard wire the heater... by that i mean cut out the quick connect and put a crimp connection?
That is most of us have done.
This did not fix the issue.. still happening. When it starts to click if i pull the filament out and cut off the end and reinsert the filament it will print fine until it starts clicking again. Any other ideas
smviens wrote:carl_m1968 wrote:A bad connection on your heater is causing it to cool.
Do you have any suggestions on how to fix this? Should i try and just hard wire the heater... by that i mean cut out the quick connect and put a crimp connection?
That is most of us have done.
do you think it may be feeding to quick?
smviens wrote:carl_m1968 wrote:A bad connection on your heater is causing it to cool.
Do you have any suggestions on how to fix this? Should i try and just hard wire the heater... by that i mean cut out the quick connect and put a crimp connection?
That is most of us have done.
Seems to be doing it on the infill, like when it retracts the filament...
there might be these reasons:
-too low temperature, add extra 5 degrees or 7 and see how it behaves
-take off the print head and clean extruder wheels, check them, maybe they are worn out? if it's possible
-your filament might have poor quality, is bent, etc.
-too long retraction, Simplify3d uses I think only 2mm retraction. For instance in Cura default of 16 mm when changing extruders on davinci 2.0 made one colour disappear on 2 colours prints on my printer . 16 mm is for nozzle switch and 4.5 for normal retraction, as default in Cura. yes I know you have one only.
-dirty nozzle inside, hard to fix. Heat up and use some thin needle to clean it inside
When you check it all , I'm almost sure it will work
I think it might be temperature. When I tried to lower temperature in middle of print , it behaved like you described. Then I pushed filament and increased temperature to previous level
In my machine, I experience that kind of noise.
What I found out is that the wheel is not biting on the filament and wheel is getting gunk too.
Cleaned it and cut the filament that have been chewed, but still no luck, it's not coming out and making that same noise.
Did my research from Soliforum, and what I found out that majority is I have something blocking inside the extruder tip.
Took out the extruder tip with a small adjustable wrench, then turn ON to heat up the extruder.
In the picture, you will see as how much was the black filament that didn't come out before and I see some debris that looks like some oil gunk.
And the extruder tip, I put on a small container and diluted with acetone to melt and for me to easily remove any gunk inside.
there might be these reasons:
-too low temperature, add extra 5 degrees or 7 and see how it behaves
-take off the print head and clean extruder wheels, check them, maybe they are worn out? if it's possible
-your filament might have poor quality, is bent, etc.
-too long retraction, Simplify3d uses I think only 2mm retraction. For instance in Cura default of 16 mm when changing extruders on davinci 2.0 made one colour disappear on 2 colours prints on my printer . 16 mm is for nozzle switch and 4.5 for normal retraction, as default in Cura. yes I know you have one only.
-dirty nozzle inside, hard to fix. Heat up and use some thin needle to clean it insideWhen you check it all , I'm almost sure it will work
I think it might be temperature. When I tried to lower temperature in middle of print , it behaved like you described. Then I pushed filament and increased temperature to previous level
I have tried changing the temp, because that what i though it was... but no luck i am using ColorFabb XT and i have tried all the way up too 260C and it has not worker... i will try and clean the extruder and let you know.
In my machine, I experience that kind of noise.
What I found out is that the wheel is not biting on the filament and wheel is getting gunk too.
Cleaned it and cut the filament that have been chewed, but still no luck, it's not coming out and making that same noise.
Did my research from Soliforum, and what I found out that majority is I have something blocking inside the extruder tip.Took out the extruder tip with a small adjustable wrench, then turn ON to heat up the extruder.
In the picture, you will see as how much was the black filament that didn't come out before and I see some debris that looks like some oil gunk.
And the extruder tip, I put on a small container and diluted with acetone to melt and for me to easily remove any gunk inside.
Thanks for the suggestion.... ill try and let you know!
SoliForum - 3D Printing Community → XYZ Printing DaVinci → Extruder Stepper Clicking!
Powered by PunBB, supported by Informer Technologies, Inc.
