1 Topic by whttnbrg

  • whttnbrg
  • Member
  • Offline
  • From: South of New Orleans
  • Registered: 2017-06-09
  • Posts: 41

Topic: Solidoodle running a Rumba with Windows 10

Windows 10 sees a unknown USB device, but wont load the driver. Have any of you setup Rumbas with Win 10? Any help and advice is appreciated.

3D Systems Cube, Hacked for Bulk Filament
Monoprice Replicator built from kit
Solidoodle 3, E3D Lite6, Rumba Upgrade
FT-i3 Mega, Looking for Dual Extruder Mods

2 Reply by Tin Falcon

  • Tin Falcon
  • Tin Falcon
  • Member
  • Offline
  • From: New Jersey, USA
  • Registered: 2014-08-01
  • Posts: 2,424

Re: Solidoodle running a Rumba with Windows 10

you may need to manually load it

Soliddoodle 4 stock w glass bed------Folger Tech Prusa 2020 upgraded to and titan /aero extruder mirror bed
FT5 with titan/ E3D Aero------MP mini select w glass bed
MP Utimate maker pro-W bondtech extruder
Marlin/Repetier Host/ Slic3r and Cura

3 Reply by knowack

  • knowack
  • Member
  • Offline
  • From: Columbia, MO
  • Registered: 2013-12-05
  • Posts: 612

Re: Solidoodle running a Rumba with Windows 10

I'm not a Rumba user.  I Googled to see what Rumba and Win10 info was out there; didn't find much.

4 Reply by wardjr

  • wardjr
  • wardjr
  • Moderator
  • Offline
  • From: Minnesota
  • Registered: 2013-06-10
  • Posts: 5,623

Re: Solidoodle running a Rumba with Windows 10

What position is the USB power jumper in? Not a win10 user but have plenty of Rumba experience. If it’s in the wrong the board won’t show up unless 12v Power is supplied.  In the USB position it receives power from the USB.  Some systems simply don’t provide enough power to run the Rumba.  I’ve had others that will be recognized with USB power only after an initial start using external power.
Just tossing around ideas for you.

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

wardjr's Website

5 Reply by whttnbrg

  • whttnbrg
  • Member
  • Offline
  • From: South of New Orleans
  • Registered: 2017-06-09
  • Posts: 41

Re: Solidoodle running a Rumba with Windows 10

The board is powered by the supernight. It works fine in windows 7, but I was looking at a using my wifes laptop since she was requesting a upgrade. I tried loading said laptop with Win7, but there are no drivers for the USB hub or the video for win7. I restored it back to 10 and it sees the board. It comes up and says unknown USB device. when you give it either of the available Rumba drivers, one says cant load because its not a signed driver, and the other errors out and crashes

3D Systems Cube, Hacked for Bulk Filament
Monoprice Replicator built from kit
Solidoodle 3, E3D Lite6, Rumba Upgrade
FT-i3 Mega, Looking for Dual Extruder Mods

6 Reply by yizhou.he

  • yizhou.he
  • yizhou.he
  • Member
  • Offline
  • From: Boston, MA
  • Registered: 2017-07-05
  • Posts: 1,322

Re: Solidoodle running a Rumba with Windows 10

https://www.maketecheasier.com/install- … windows10/

(Da Vinci 1.0, Jr. 1.0 RAMPS, miniMaker) X4, (Creality CR-10S, CR-10 mini, Ender-3) X4, Anycubic MEGA X4, Anycubic Chrion X1, ADMILAB Gantry X2 (MonoPrice Maker Select V2, Plus, Ultimate)X4--Select mini X1, Anycubic photon X4, Wanhao duplicate D7 X1.
iNSTONE Inventor Pro X2, CTC Dual X2, ANET-A8, Hictop 3DP-11, Solidoodle Press, FLSUN I3 2017X1

7 Reply by carl_m1968

  • carl_m1968
  • carl_m1968
  • Member
  • Offline
  • From: Far North almost not Dallas
  • Registered: 2014-10-17
  • Posts: 6,512

Re: Solidoodle running a Rumba with Windows 10

whttnbrg wrote:

The board is powered by the supernight. It works fine in windows 7, but I was looking at a using my wifes laptop since she was requesting a upgrade. I tried loading said laptop with Win7, but there are no drivers for the USB hub or the video for win7. I restored it back to 10 and it sees the board. It comes up and says unknown USB device. when you give it either of the available Rumba drivers, one says cant load because its not a signed driver, and the other errors out and crashes


Google installing Unsigned drivers. It can be done..

Printing since 2009 and still love it!
Anycubic 4MAX best $225 ever invested.
Voxelabs Proxima SLA. 6 inch 2k Mono LCD.
Anycubic Predator, massive Delta machine. 450 x 370 print envelope.