1 Topic by seven2099

  • seven2099
  • Member
  • Offline
  • Registered: 2015-03-03
  • Posts: 101

Topic: Solidoodle Press motherboard replacement

Hello all

Seems my solidoodle motherboard has gone caput. Either that or the PSU has died, however when measuring with multimeter it seems i'm getting the 24v DC that should be coming out of there.

Is there any known plug and play replacements for this board?

Kind regards,

Seven

2 Reply by Kronikabuse

  • Kronikabuse
  • Kronikabuse
  • Member
  • Offline
  • From: Wi
  • Registered: 2014-08-03
  • Posts: 709

Re: Solidoodle Press motherboard replacement

www.printitindustries.com has them. or you could upgrade to a better controller cheaply with a ramps 1.4 board or for a bit more money (completely worth it) a duet wifi. youll need to do some wiring with both

Sd4 #9080 with a glass bed. E3d chimera duel extruder. Paste extruder , duet wifi.
Lawsy carriages. linear bearings. Y axis direct drive, Kinect scanner
SD4#8188 glass bed, lawsly carriages, E3d v6, octoprint http://www.ustream.tv/channel/hotrod96z28
Filastruder/filawinder, Custom Delta 300mm x 600mm

3 Reply by seven2099 (edited by seven2099 2017-06-09 21:01:02)

  • seven2099
  • Member
  • Offline
  • Registered: 2015-03-03
  • Posts: 101

Re: Solidoodle Press motherboard replacement

Kronikabuse wrote:

www.printitindustries.com has them. or you could upgrade to a better controller cheaply with a ramps 1.4 board or for a bit more money (completely worth it) a duet wifi. youll need to do some wiring with both

Thanks for the response man.

I dont see to find it anywhere on the site.

Its worth mentioning I have a solidoodle press and while I've read about ramps, rumba and other boards I can't seem to find anyone who gets it fully working again - including the auto bed leveling (with a clear guide on what to do)

Any help you can provide would be appreciated - will gladly read up however I'm not even sure what the parts list I'd need to purchase.

4 Reply by heartless

  • heartless
  • heartless
  • Member
  • Offline
  • From: Northcentral Wisconsin
  • Registered: 2015-04-08
  • Posts: 2,152

Re: Solidoodle Press motherboard replacement

you might have better luck with this in the Press specific section

SD4 #1 & #2 - Lawsy carriages, E3D v6, Rumba controller board, mirror bed plate, X motor fan, upgraded PSU & Mica bed heater
SD4 #3 - in the works ~ Folgertech FT-5, rev 1
Printit Industries Beta Tester - Horizon H1

5 Reply by AZERATE

  • AZERATE
  • AZERATE
  • PRINTiT
  • Offline
  • From: Chicago
  • Registered: 2013-11-28
  • Posts: 2,077

Re: Solidoodle Press motherboard replacement

seven2099 wrote:
Kronikabuse wrote:

www.printitindustries.com has them. or you could upgrade to a better controller cheaply with a ramps 1.4 board or for a bit more money (completely worth it) a duet wifi. youll need to do some wiring with both

Thanks for the response man.

I dont see to find it anywhere on the site.

Its worth mentioning I have a solidoodle press and while I've read about ramps, rumba and other boards I can't seem to find anyone who gets it fully working again - including the auto bed leveling (with a clear guide on what to do)

Any help you can provide would be appreciated - will gladly read up however I'm not even sure what the parts list I'd need to purchase.

https://www.printitindustries.com/produ … wer-supply

Printit Mason and Printit Horizon printers
Multiple SD2s- Bulldog XL, E3D v5/v6/Lite6, Volcano, Hobb Goblin, Titan, .9 motor, Lawsy carriages, direct Y drive, fishing line...the list goes on
Filawinder and Filastruder #1870.....worth every penny!

6 Reply by seven2099

  • seven2099
  • Member
  • Offline
  • Registered: 2015-03-03
  • Posts: 101

Re: Solidoodle Press motherboard replacement

AZERATE wrote:
seven2099 wrote:
Kronikabuse wrote:

www.printitindustries.com has them. or you could upgrade to a better controller cheaply with a ramps 1.4 board or for a bit more money (completely worth it) a duet wifi. youll need to do some wiring with both

Thanks for the response man.

I dont see to find it anywhere on the site.

Its worth mentioning I have a solidoodle press and while I've read about ramps, rumba and other boards I can't seem to find anyone who gets it fully working again - including the auto bed leveling (with a clear guide on what to do)

Any help you can provide would be appreciated - will gladly read up however I'm not even sure what the parts list I'd need to purchase.

https://www.printitindustries.com/produ … wer-supply

Thanks sir

However it's actually the motherboard, not the PSU. As I said in my original post, I've tested the PSU and its definitely outputting 24v.

Motherboard however fails to light up anymore.

I've also posted in the press section and no answers yet sad