1,981 Belt was loose and skipped how to fix.
by bstaffa042
- 1 reply
- 1,275 views
- Last post 2014-11-19 06:39:13 by carl_m1968
1,982 Z axis m3 rod mod Upgrade
by drewsfjord
- 0 replies
- 1,021 views
- Last post 2014-11-18 14:32:22 by drewsfjord
1,983 Malware? Fixed and running! SD card Bug? waiting to attack?
by drewsfjord
- 6 replies
- 3,090 views
- Last post 2014-11-18 14:26:02 by drewsfjord
1,984 extruder temp
by dudad.net
- 6 replies
- 3,697 views
- Last post 2014-11-18 14:19:38 by dudad.net
1,985 Print job failure
by patelsp92
- 3 replies
- 3,704 views
- Last post 2014-11-17 17:45:07 by POPOTROPOPIC3
1,986 [Custom Firmware] Z Axis Wont Go Into Nagitives
by Hurleyboarder
- 2 replies
- 1,558 views
- Last post 2014-11-17 15:00:54 by Hurleyboarder
1,987 3d modeling question (Rhino)
by heidkampn1
- 0 replies
- 1,115 views
- Last post 2014-11-16 22:36:36 by heidkampn1
1,988 How to Guide - Craftware and Notepad++ Gcode hack
by grantgibson45
- 0 replies
- 1,987 views
- Last post 2014-11-16 15:12:53 by grantgibson45
1,989 just a little off....
by rawkstar320
- 4 replies
- 2,567 views
- Last post 2014-11-16 14:56:40 by scobo
1,990 Printed circle accuracy
by scobo
- 1 reply
- 1,441 views
- Last post 2014-11-16 12:28:26 by scobo
1,991 Heat Beds for Da Vinci 1.0
by andysteed
- 9 replies
- 9,222 views
- Last post 2014-11-16 10:47:27 by Jrard
- 14 replies
- 8,021 views
- Last post 2014-11-15 21:55:33 by scobo
1,993 How to get best quality prints from XYZ Da Vinci 1.0
by Jrard
- 24 replies
- 17,384 views
- Last post 2014-11-15 21:22:33 by carl_m1968
1,994 Microcenter
by dale
- 1 reply
- 1,599 views
- Last post 2014-11-15 09:41:33 by drewsfjord
1,995 Da Vinci 1.0 with E3Dv6 printing ColorFabb bronze
by djmechespina
- 1 reply
- 977 views
- Last post 2014-11-15 07:03:36 by drewsfjord
1,996 Still trying to figure out this Repetier thing
by ShadowWizard
- 8 replies
- 4,636 views
- Last post 2014-11-15 03:56:56 by POPOTROPOPIC3
1,997 Printing PET with XYZ Davinci
by markD3
- 2 replies
- 2,082 views
- Last post 2014-11-13 18:01:52 by carl_m1968
1,998 Calibration and Extruder to Bed Clearance Questions & Discussion
by eriemaker
- 2 replies
- 2,365 views
- Last post 2014-11-13 17:34:20 by eriemaker
1,999 Printing PET with XYZ Davinci
by markD3
- 0 replies
- 670 views
- Last post 2014-11-13 11:21:46 by markD3
2,000 Da Vinci 1.0 with E3Dv6 printing ColorFabb bronze
by djmechespina
- 0 replies
- 862 views
- Last post 2014-11-12 02:05:03 by djmechespina
2,001 Da Vinci 1.0 with E3Dv6 printing ColorFabb bronze
by djmechespina
- 0 replies
- 701 views
- Last post 2014-11-12 02:04:51 by djmechespina
2,002 Centering Prints with Repetier Host and Firmware
by carl_m1968
- 0 replies
- 1,184 views
- Last post 2014-11-11 05:08:19 by carl_m1968
2,003 Calibration issues / ideas
by Alex_B
- 8 replies
- 5,627 views
- Last post 2014-11-10 22:53:38 by Alex_B
2,004 I have problems at the start of printing, please help!
by mamamosca
- 13 replies
- 6,195 views
- Last post 2014-11-09 22:20:02 by scotthay
2,005 Unresponsive printer
by dale
- 4 replies
- 6,282 views
- Last post 2014-11-09 17:49:35 by dale
- 0 replies
- 1,153 views
- Last post 2014-11-09 13:03:31 by Eder
2,007 Filament comes out when being loaded, nothing comes out when printing
by talimore
- 5 replies
- 5,836 views
- Last post 2014-11-09 06:45:28 by carl_m1968
2,008 How To ? - KISSlicer setup using XYZ config
by knucklbustr
- 0 replies
- 1,697 views
- Last post 2014-11-09 04:10:09 by knucklbustr
2,009 Error 0030 Things to check?
by wesalbert
- 0 replies
- 1,220 views
- Last post 2014-11-07 04:59:08 by wesalbert
2,010 Hotend Mount/Holder X axis upgrade?
by drewsfjord
- 0 replies
- 1,075 views
- Last post 2014-11-05 11:27:01 by drewsfjord