<![CDATA[SoliForum - 3D Printing Community — Soliprint V1.1.1]]> https://www.soliforum.com/topic/9869/soliprint-v111/ Fri, 13 Feb 2015 01:28:49 +0000 PunBB <![CDATA[Re: Soliprint V1.1.1]]> https://www.soliforum.com/post/85009/#p85009 I actually just figured it out.  I had to switch from virtual printer to com 4.   Printing with it right now. Thanks for the response.

]]> Fri, 13 Feb 2015 01:28:49 +0000 https://www.soliforum.com/post/85009/#p85009 <![CDATA[Re: Soliprint V1.1.1]]> https://www.soliforum.com/post/84967/#p84967 neiledit wrote:

...I am however having trouble connecting my press to  RH. I can't get it to respond to any inputs. Any help there?

This probably should be in another thread, however... Are you unable to connect, or is it that you connect and then you're unable to do anything?  I got the RH from the solidoodle website and then upgraded slic3r to the latest and it seems to work well. You need to remember to add the z-probing code to the start gcode though.

]]> Thu, 12 Feb 2015 22:41:54 +0000 https://www.soliforum.com/post/84967/#p84967 <![CDATA[Re: Soliprint V1.1.1]]> https://www.soliforum.com/post/84862/#p84862 I'm having similar experience to android78. My extruder temps needs to be at 230 or higher for longer prints and the z calibration can run but doesn't work incredibly well. I am however having trouble connecting my press to  RH. I can't get it to respond to any inputs. Any help there?

]]> Thu, 12 Feb 2015 13:49:09 +0000 https://www.soliforum.com/post/84862/#p84862 <![CDATA[Re: Soliprint V1.1.1]]> https://www.soliforum.com/post/84794/#p84794 I installed it.  A couple of things I noticed:
1. It still doesn't print well.  I find that I need to set the nozzle temp to at least 230 to get any adhesion between layers after the first couple and there is no way to adjust the temp in this software.
2. The z-calibration now works.  At least, it prints lines, but it doesn't seem to help.  Seems that the accuracy in z axis is very poor in my printer, so it will print higher with lines it prints going from front to back then it does from back to front.  I suggest they should print two lines for each height so that we can choose the one that prints best in both directions.
3.  Don't use scale and rotate. Doing so means it seems unable to position the part on the print bed.  This issue was in the previous version too.

Sticking with RH for now.

]]> Wed, 11 Feb 2015 23:49:10 +0000 https://www.soliforum.com/post/84794/#p84794 <![CDATA[Re: Soliprint V1.1.1]]> https://www.soliforum.com/post/84694/#p84694 I installed this last night and tried it out. One thing I noticed immediately is that the prints went MUCH faster. I wonder if there weren't additional settings tweaks that they didn't state.

]]> Wed, 11 Feb 2015 15:01:38 +0000 https://www.soliforum.com/post/84694/#p84694 <![CDATA[Re: Soliprint V1.1.1]]> https://www.soliforum.com/post/84637/#p84637 I've been running it since I got the printer (which was about 10 hours ago).  I'm pretty new to 3d printing and 1.1.1 so I don't know how much help I can be.  I do know the z calibration worked pretty well.

]]> Wed, 11 Feb 2015 04:37:41 +0000 https://www.soliforum.com/post/84637/#p84637 <![CDATA[Soliprint V1.1.1]]> https://www.soliforum.com/post/84620/#p84620 Anyone tried it yet?

]]> Wed, 11 Feb 2015 03:46:29 +0000 https://www.soliforum.com/post/84620/#p84620