<![CDATA[SoliForum - 3D Printing Community — Z-Offset Calibration]]> https://www.soliforum.com/topic/9749/zoffset-calibration/ Fri, 27 Feb 2015 20:39:23 +0000 PunBB <![CDATA[Re: Z-Offset Calibration]]> https://www.soliforum.com/post/87522/#p87522 The Z-Calibration is set/retrieved using the M851 command, and saved to firmware using M500.  I discussed this in the Calibration Sticky here: http://www.soliforum.com/post/84010/#p84010

Once you have the value set in firmware, you can use any software to print, as long as you use G29 to home the Z-Axis before printing.

]]> Fri, 27 Feb 2015 20:39:23 +0000 https://www.soliforum.com/post/87522/#p87522 <![CDATA[Re: Z-Offset Calibration]]> https://www.soliforum.com/post/87517/#p87517 Does anyone know what parameter this is stored in on the printer?

]]> Fri, 27 Feb 2015 19:59:09 +0000 https://www.soliforum.com/post/87517/#p87517 <![CDATA[Re: Z-Offset Calibration]]> https://www.soliforum.com/post/83821/#p83821 Robny wrote:

Is your computer/software recognizing the printer?

Yes.

rrssll wrote:

Try homing the X & Y axis first?

Did that.

BT wrote:

Once your printer is detected and selected, you will need to wait for the temperatures to reach its starting temp. Then it will start z calibration. Can take over 10 minutes depending how cold your room is.

Ok i have not waited that long... would try that.
THanks!

]]> Sat, 07 Feb 2015 07:28:43 +0000 https://www.soliforum.com/post/83821/#p83821 <![CDATA[Re: Z-Offset Calibration]]> https://www.soliforum.com/post/83810/#p83810 Once your printer is detected and selected, you will need to wait for the temperatures to reach its starting temp. Then it will start z calibration. Can take over 10 minutes depending how cold your room is.

]]> Sat, 07 Feb 2015 05:59:16 +0000 https://www.soliforum.com/post/83810/#p83810 <![CDATA[Re: Z-Offset Calibration]]> https://www.soliforum.com/post/83809/#p83809 Try homing the X & Y axis first?

]]> Sat, 07 Feb 2015 05:56:59 +0000 https://www.soliforum.com/post/83809/#p83809 <![CDATA[Re: Z-Offset Calibration]]> https://www.soliforum.com/post/83805/#p83805 Is your computer/software recognizing the printer?

]]> Sat, 07 Feb 2015 05:39:09 +0000 https://www.soliforum.com/post/83805/#p83805 <![CDATA[Z-Offset Calibration]]> https://www.soliforum.com/post/83748/#p83748 Finally have time to setup the Press, following the "Press Calibration Instructions" Thread

I presume to be expecting the printer to print a few lines when i hit "Z-offset Calibration > Run Calibration Test"
But nothing happened. nothings printing nothings moving.

I only see the initial Z-Offset value changes.

Am i missing out something?

P.S: I downgrade the soliprint software to 1.0, as i researched that 1.1 z offset is not working

Thanks in advance

]]> Sat, 07 Feb 2015 02:39:27 +0000 https://www.soliforum.com/post/83748/#p83748