Thanks again!

The only advice I have for people doing this is to not close teensy when it pops open after compiling. If you click file > open hex file, it will bring you directly to the folder it saved Marlin.cpp.hex in. Mine was not saving in the temp folder. Also, don't forget to change your extruder steps per mm in the EEPROM settings after you install the firmware. It can be quite a scare when you start printing and nothing is coming out.

Again, thank you so much. Super appreciated over here!

https://github.com/ozadr1an/Solidoodle- … guration.h
you are loading the M600 and you want this one instead.  It is the one I am currently using and it is newer.
You shouldn't have to worry about any of the filament alarm stuff.

Awesome, thank you. I'll flash it and let you know how it all turns out.

fdm_process wrote:

This is the version I downloaded: https://github.com/ozadr1an/Solidoodle- … guration.h  I now see a newer version that was last edited 5 hours ago. I'm going to download that one and give it a go.

This is the one you want and is the one I use.
You don't actually delete anything you just comment the lines out  using //.
Most of the time you can just comment out the first main line. 
Give me a about 30 minutes and I'll get you a screen shot of that section.

Okay, but I just put the // in front of all the stuff having to do with the filament alarm and the park head enable. So, three things in there I killed.

I'll wait for your image before I flash.

This is the version I downloaded: https://github.com/ozadr1an/Solidoodle- … guration.h  I now see a newer version that was last edited 5 hours ago. I'm going to download that one and give it a go.

This is the one you want and is the one I use.
You don't actually delete anything you just comment the lines out  using //.
Most of the time you can just comment out the first main line. 
Give me a about 30 minutes and I'll get you a screen shot of that section.

// Filament Alarm Pin (+684 Bytes)
// Must ensure PARK_HEAD_ENABLE is defined below as well!
//#define FILAMENT_ALARM_PIN 63 //RAMPS Pin for Microswitch on Filament Feed. D63 on AUX2 with a GND next to it.
#define FILAMENT_ALARM_PIN 4 //Sang Pin for Microswitch on Filament Feed. A4 pin, with a GND Next to it.
#define PAUSE_HEATER_DELAY 300 //Delay until heater disabled when paused in seconds

// Enable support for head parking/print pausing/filament changeover support (M600 + M601) (+2780 Bytes)
// REQUIRED FOR FILAMENT_ALARM!
#define PARK_HEAD_ENABLE

#include "Configuration_adv.h"
#include "thermistortables.h"

#endif //__CONFIGURATION

wardjr wrote:

The other thing is you can open the Config file from any location so it really doesn't matter.
Are you opening a marlin.pde or Marlin.ino?

Maybe I am doing this part wrong. I was trying to open the configuration.h file in arduino to edit it, then I was going to save it and move the .hex file into the bootloader folder and open DOS to run the bootloader.

Your doing it right but by this point you most likely have more than one Marlin folder. You want to be opening the .ino file from the Marlin V1 beta folder (something like that). Then navigate to the configuration.h tab.  Make your changes verify and save then work through the flash process.
I will have some time later to send you a link to the firmware.  Maybe you just grabbed the wrong one.  If you have a link post it and I can verify.

The other thing is you can open the Config file from any location so it really doesn't matter.
Are you opening a marlin.pde or Marlin.ino?

Maybe I am doing this part wrong. I was trying to open the configuration.h file in arduino to edit it, then I was going to save it and move the .hex file into the bootloader folder and open DOS to run the bootloader.