<![CDATA[SoliForum - 3D Printing Community — Press has an internal mounts for Raspberry Pi]]> https://www.soliforum.com/topic/9557/press-has-an-internal-mounts-for-raspberry-pi/ Mon, 02 Feb 2015 00:35:40 +0000 PunBB <![CDATA[Re: Press has an internal mounts for Raspberry Pi]]> https://www.soliforum.com/post/82820/#p82820 cptskippy wrote:

Are there pin outs on the Press's motherboard for the USB port or if you installed a raspberry Pi would you have to run a cable externally to plug into the USB?

Just looking at the picture, it looks like the pins just near the USB port on the solidoodle board would probably be USB access.

]]> Mon, 02 Feb 2015 00:35:40 +0000 https://www.soliforum.com/post/82820/#p82820 <![CDATA[Re: Press has an internal mounts for Raspberry Pi]]> https://www.soliforum.com/post/82222/#p82222 Are there pin outs on the Press's motherboard for the USB port or if you installed a raspberry Pi would you have to run a cable externally to plug into the USB?

]]> Thu, 29 Jan 2015 14:57:22 +0000 https://www.soliforum.com/post/82222/#p82222 <![CDATA[Re: Press has an internal mounts for Raspberry Pi]]> https://www.soliforum.com/post/82098/#p82098 Wifi would have been nice. Serial over USB isn't something I've had to use in quite a long time.

]]> Wed, 28 Jan 2015 21:38:22 +0000 https://www.soliforum.com/post/82098/#p82098 <![CDATA[Re: Press has an internal mounts for Raspberry Pi]]> https://www.soliforum.com/post/82092/#p82092 IanJohnson wrote:

I was wondering why, when designing a brand new consumer appliance looking printer, they didn't include an LCD and SD slot for independent operation.  This must be the reason.  An LCD is actually a terrible UI for a 3D printer, putting their effort into remote browser based operation is a better choice.  If they were planning on integrating it into Soliprint, it is probably rather far off, considering the current state of the program.

Think of all the software they wouldn't have to write if they had just gone from octoprint at the start. They could have touted it as a "Wi-Fi ready" printer . . . wink

]]> Wed, 28 Jan 2015 21:26:28 +0000 https://www.soliforum.com/post/82092/#p82092 <![CDATA[Re: Press has an internal mounts for Raspberry Pi]]> https://www.soliforum.com/post/82084/#p82084 I was wondering why, when designing a brand new consumer appliance looking printer, they didn't include an LCD and SD slot for independent operation.  This must be the reason.  An LCD is actually a terrible UI for a 3D printer, putting their effort into remote browser based operation is a better choice.  If they were planning on integrating it into Soliprint, it is probably rather far off, considering the current state of the program.

]]> Wed, 28 Jan 2015 20:30:37 +0000 https://www.soliforum.com/post/82084/#p82084 <![CDATA[Re: Press has an internal mounts for Raspberry Pi]]> https://www.soliforum.com/post/82031/#p82031 Hmm... this makes me wonder if there's a sufficiently powerful 5v power point on the motherboard to power said Pi.

]]> Wed, 28 Jan 2015 16:31:32 +0000 https://www.soliforum.com/post/82031/#p82031 <![CDATA[Press has an internal mounts for Raspberry Pi]]> https://www.soliforum.com/post/82028/#p82028 Rejoice! people who love octoprint.

There are screw mounts next to the Press's motherboard that perfectly fit a raspberry pi~!

http://i.imgur.com/KkIaHfu.jpg

http://i.imgur.com/o41DT9S.jpg


Source:
http://www.reddit.com/r/3Dprinting/comm … ss_has_an/
http://imgur.com/a/9OYov

]]> Wed, 28 Jan 2015 16:08:53 +0000 https://www.soliforum.com/post/82028/#p82028