<![CDATA[SoliForum - 3D Printing Community — How do I wire up my RUMBA with a xbox power supply?]]> https://www.soliforum.com/topic/9480/how-do-i-wire-up-my-rumba-with-a-xbox-power-supply/ Tue, 27 Jan 2015 06:16:06 +0000 PunBB <![CDATA[Re: How do I wire up my RUMBA with a xbox power supply?]]> https://www.soliforum.com/post/81818/#p81818 Thanks elmoret and wardjr! You guys rock!

]]> Tue, 27 Jan 2015 06:16:06 +0000 https://www.soliforum.com/post/81818/#p81818 <![CDATA[Re: How do I wire up my RUMBA with a xbox power supply?]]> https://www.soliforum.com/post/81664/#p81664 If you are not using a stepper driver you should remove it. 
note:  You also should remove them if you are powering the board with out motors attached.  Say for flashing.
Your crimps are fine but not needed for the screw terminals.
If you want to run the board without having a heater plugged in you should be fine as long as you don't call for heat.
If you are worried about it just leave the HB-PWR wires disconnected.  The board will function just fine without power to the HB circuit.
http://i.imgur.com/4S1CdxV.png

Hope this answers your questions.

]]> Mon, 26 Jan 2015 17:42:39 +0000 https://www.soliforum.com/post/81664/#p81664 <![CDATA[Re: How do I wire up my RUMBA with a xbox power supply?]]> https://www.soliforum.com/post/81583/#p81583 Also, if i do not have a heated bed plugged in, will it matter if I turn it on? (I really do not want to make a mistake)

]]> Mon, 26 Jan 2015 05:03:07 +0000 https://www.soliforum.com/post/81583/#p81583 <![CDATA[Re: How do I wire up my RUMBA with a xbox power supply?]]> https://www.soliforum.com/post/81436/#p81436 How does this look for crimping?
http://i.imgur.com/nbepqHD.jpg

]]> Sun, 25 Jan 2015 05:48:12 +0000 https://www.soliforum.com/post/81436/#p81436 <![CDATA[Re: How do I wire up my RUMBA with a xbox power supply?]]> https://www.soliforum.com/post/81435/#p81435 How does this look for crimping? Also, if I am not using a stepper driver, should I take it out?
http://i.imgur.com/nbepqHD.jpg

]]> Sun, 25 Jan 2015 05:47:34 +0000 https://www.soliforum.com/post/81435/#p81435 <![CDATA[Re: How do I wire up my RUMBA with a xbox power supply?]]> https://www.soliforum.com/post/81415/#p81415 Yep

]]> Sun, 25 Jan 2015 02:49:20 +0000 https://www.soliforum.com/post/81415/#p81415 <![CDATA[Re: How do I wire up my RUMBA with a xbox power supply?]]> https://www.soliforum.com/post/81407/#p81407 Don't use the 5sb wires.

2x 12v to heater bed +
2x GND to heater bed -
1x 12v to the other + (main)
1x GND to the other - (main)

]]> Sun, 25 Jan 2015 01:57:55 +0000 https://www.soliforum.com/post/81407/#p81407 <![CDATA[How do I wire up my RUMBA with a xbox power supply?]]> https://www.soliforum.com/post/81405/#p81405 http://i.imgur.com/HGQU4GH.jpg

Okay, so from the picture above this is my plan to wire up the RUMBA.

http://i.imgur.com/WiC7JHJ.jpg

I am checking in with guys first to make sure  do not do anything that will cost me my board. What do I end up doing with the 3 ground wires?

]]> Sun, 25 Jan 2015 01:45:34 +0000 https://www.soliforum.com/post/81405/#p81405