SoliForum - 3D Printing Community — Jsut got my Press, trying to calibrate but filament bunches up

Re: Jsut got my Press, trying to calibrate but filament bunches up

null@example.com (android78) — Sat, 21 Feb 2015 23:52:37 +0000

If you use hair spray for helping the filament stick to the bed just beware that most don't appear to work. At least that's my experience in australia. The only one that seems to work is a very expensive redkin one. UHU glue stick is a lot cheaper but harder to apply.

Re: Jsut got my Press, trying to calibrate but filament bunches up

null@example.com (scruffybob) — Sat, 21 Feb 2015 17:15:14 +0000

Two possible probelms:

1. Not sticking to the glass: One thing they don't tell you is that the ABS doesn't stick to the glass very well. Get a glue stick (or hairsprary or painter's tape) and coat the glass prior to running the print. I prefer the glue stick. I put a thin coat on right before printing and it is still tacky enough to cause the first layer to stick when it starts printing. I suspect that's the problem here.

2. Extruder slightly too high. In Soliprint 1.1.1, look for the Z-offset calibration and run that to fine-tune the height. If you're a little too high, the first layer won't stick to the glass and will bunch up like this.

Re: Jsut got my Press, trying to calibrate but filament bunches up

null@example.com (celboy) — Sat, 21 Feb 2015 12:30:18 +0000

Yes Yeezy…that all looks very familiar

thanks for posting

TomT

Re: Jsut got my Press, trying to calibrate but filament bunches up

null@example.com (Yeezy) — Sat, 21 Feb 2015 10:38:42 +0000

Is it something like this?

https://www.youtube.com/watch?v=ejfvJAjYzMc

Re: Jsut got my Press, trying to calibrate but filament bunches up

null@example.com (celboy) — Sat, 21 Feb 2015 05:37:57 +0000

So being a newbie to this-----its strictly a heat issue---not an extruder issue?

I mean if the filament is coming out than extruder is working right?

Then its either the temp of the chamber or the heat of the glass thats causing the bunching?
Wow!
Do I jack up my bed temp?

Its definitely not plug & play. I would 've preferred a better manual explaining more---things I'm learning here on the forums.

Any tips would be appreciated.

TomT

Re: Jsut got my Press, trying to calibrate but filament bunches up

null@example.com (wire10ga) — Fri, 16 Jan 2015 12:48:50 +0000

For ABS, yes you want a closed area to keep the chamber warm so that the ABS will not delaminate from the previous layers.

Re: Jsut got my Press, trying to calibrate but filament bunches up

null@example.com (kevman) — Fri, 16 Jan 2015 04:12:23 +0000

Perhaps I am doing something wrong, I was trying to watch the action so I had all the doors open, is it best practice to keep everything closed ?

Re: Jsut got my Press, trying to calibrate but filament bunches up

null@example.com (wire10ga) — Thu, 15 Jan 2015 23:18:37 +0000

Video? Photos? These are new, so you have to provide something to help out the experts here ( not me ) figure out what might be wrong.

Jsut got my Press, trying to calibrate but filament bunches up

null@example.com (kevman) — Thu, 15 Jan 2015 23:04:16 +0000

Any idea? It seems to just stick to the extruder. Also it does some grinding here and there when it tries to move.

Thanks

Kevin