<![CDATA[SoliForum - 3D Printing Community — GCode Ref & Reusing XYZ Cartridges]]> https://www.soliforum.com/topic/8973/gcode-ref-reusing-xyz-cartridges/ Tue, 13 Jan 2015 14:27:22 +0000 PunBB <![CDATA[Re: GCode Ref & Reusing XYZ Cartridges]]> https://www.soliforum.com/post/78736/#p78736 I measured an empty spool just then it weighed about 125g and that was only for the spool that comes inside the plastic housing.

]]> Tue, 13 Jan 2015 14:27:22 +0000 https://www.soliforum.com/post/78736/#p78736 <![CDATA[Re: GCode Ref & Reusing XYZ Cartridges]]> https://www.soliforum.com/post/78703/#p78703 I didn't measure or weigh it, but I can next time I have one out. I just wound it up till it was pretty full. I've reloaded with PVA, HIPS, and ABS.

]]> Tue, 13 Jan 2015 03:39:04 +0000 https://www.soliforum.com/post/78703/#p78703 <![CDATA[Re: GCode Ref & Reusing XYZ Cartridges]]> https://www.soliforum.com/post/78702/#p78702 I reloaded 1 today myself I had a total weight of 692 grams with spool and filament. But I forgot to weigh the spool first to see what the empty weight of the spool was.
Jon

]]> Tue, 13 Jan 2015 03:29:35 +0000 https://www.soliforum.com/post/78702/#p78702 <![CDATA[Re: GCode Ref & Reusing XYZ Cartridges]]> https://www.soliforum.com/post/78593/#p78593 bryan,

How much did you reload into cartridge? Are you getting more than the 600g/240meters that (I think) is in a standard one?

This is just for ABS..right?

Thanks

Jay

]]> Mon, 12 Jan 2015 14:32:51 +0000 https://www.soliforum.com/post/78593/#p78593 <![CDATA[Re: GCode Ref & Reusing XYZ Cartridges]]> https://www.soliforum.com/post/77358/#p77358 Thanks Bryan! Exactly what I was looking for.

]]> Sat, 03 Jan 2015 21:30:11 +0000 https://www.soliforum.com/post/77358/#p77358 <![CDATA[Re: GCode Ref & Reusing XYZ Cartridges]]> https://www.soliforum.com/post/77168/#p77168 I like using and refilling the cartridges. They keep the filament tidy and clean, and with the desiccant pouch inside, dry as well.

I printed Aaron's filament rewinder tool and I can refill a cartridge in probably 5 minutes or so. You stick a 1/4" hex bit into it's socket and turn it with a drill or cordless screwdriver. Let the host spool spin on a horizontal shaft.

http://voltivo.com/forum/davinci-filame … inder-tool

]]> Fri, 02 Jan 2015 05:22:49 +0000 https://www.soliforum.com/post/77168/#p77168 <![CDATA[Re: GCode Ref & Reusing XYZ Cartridges]]> https://www.soliforum.com/post/77167/#p77167 This is in the Repetier.ino Arduino file:

\section GCodes Implemented GCodes

 look here for descriptions of gcodes: http://linuxcnc.org/handbook/gcode/g-code.html
 and http://objects.reprap.org/wiki/Mendel_User_Manual:_RepRapGCodes

Implemented Codes

- G0  -> G1
- G1  - Coordinated Movement X Y Z E, S1 disables boundary check, S0 enables it
- G4  - Dwell S<seconds> or P<milliseconds>
- G20 - Units for G0/G1 are inches.
- G21 - Units for G0/G1 are mm.
- G28 - Home all axis or named axis.
- G29 S<0..2> - Z-Probe at the 3 defined probe points. S = 1 measure avg. zHeight, S = 2 store avg zHeight
- G30 P<0..3> - Single z-probe at current position P = 1 first measurement, P = 2 Last measurement P = 0 or 3 first and last measurement
- G31 - Write signal of probe sensor
- G32 S<0..2> P<0..1> - Autolevel print bed. S = 1 measure zLength, S = 2 Measue and store new zLength
- G90 - Use absolute coordinates
- G91 - Use relative coordinates
- G92 - Set current position to cordinates given
- G131 - set extruder offset position to 0 - needed for calibration with G132
- G132 - calibrate endstop positions. Call this, after calling G131 and after centering the extruder holder.

RepRap M Codes

- M104 - Set extruder target temp
- M105 - Read current temp
- M106 - Fan on
- M107 - Fan off
- M109 - Wait for extruder current temp to reach target temp.
- M114 - Display current position

Custom M Codes

- M20  - List SD card
- M21  - Init SD card
- M22  - Release SD card
- M23  - Select SD file (M23 filename.g)
- M24  - Start/resume SD print
- M25  - Pause SD print
- M26  - Set SD position in bytes (M26 S12345)
- M27  - Report SD print status
- M28  - Start SD write (M28 filename.g)
- M29  - Stop SD write
- M30 <filename> - Delete file on sd card
- M32 <dirname> create subdirectory
- M42 P<pin number> S<value 0..255> - Change output of pin P to S. Does not work on most important pins.
- M80  - Turn on power supply
- M81  - Turn off power supply
- M82  - Set E codes absolute (default)
- M83  - Set E codes relative while in Absolute Coordinates (G90) mode
- M84  - Disable steppers until next move,
        or use S<seconds> to specify an inactivity timeout, after which the steppers will be disabled.  S0 to disable the timeout.
- M85  - Set inactivity shutdown timer with parameter S<seconds>. To disable set zero (default)
- M92  - Set axisStepsPerMM - same syntax as G92
- M99 S<delayInSec> X0 Y0 Z0 - Disable motors for S seconds (default 10) for given axis.
-M100 clean nozzle
-M101 turn light on (no eeprom saving) and reset autoturn off time if activated
-M102 turn light off (no eeprom saving)
- M104 S<temp> T<extruder> P1 F1 - Set temperature without wait. P1 = wait for moves to finish, F1 = beep when temp. reached first time
- M105 X0 - Get temperatures. If X0 is added, the raw analog values are also written.
- M112 - Emergency kill
- M115- Capabilities string
- M116 - Wait for all temperatures in a +/- 1 degree range
- M117 <message> - Write message in status row on lcd
- M119 - Report endstop status
- M140 S<temp> F1 - Set bed target temp, F1 makes a beep when temperature is reached the first time
- M190 - Wait for bed current temp to reach target temp.
- M201 - Set max acceleration in units/s^2 for print moves (M201 X1000 Y1000)
- M202 - Set max acceleration in units/s^2 for travel moves (M202 X1000 Y1000)
- M203 - Set temperture monitor to Sx
- M204 - Set PID parameter X => Kp Y => Ki Z => Kd S<extruder> Default is current extruder. NUM_EXTRUDER=Heated bed
- M205 - Output EEPROM settings
- M206 - Set EEPROM value
- M207 X<XY jerk> Z<Z Jerk> E<ExtruderJerk> - Changes current jerk values, but do not store them in eeprom.
- M220 S<Feedrate multiplier in percent> - Increase/decrease given feedrate
- M221 S<Extrusion flow multiplier in percent> - Increase/decrease given flow rate
- M231 S<OPS_MODE> X<Min_Distance> Y<Retract> Z<Backlash> F<ReatrctMove> - Set OPS parameter
- M232 - Read and reset max. advance values
- M233 X<AdvanceK> Y<AdvanceL> - Set temporary advance K-value to X and linear term advanceL to Y
- M251 Measure Z steps from homing stop (Delta printers). S0 - Reset, S1 - Print, S2 - Store to Z length (also EEPROM if enabled)
- M280 S<mode> - Set ditto printing mode. mode: 0 = off, 1 = on
- M300 S<Frequency> P<DurationMillis> play frequency
- M303 P<extruder/bed> S<printTemerature> X0 - Autodetect pid values. Use P<NUM_EXTRUDER> for heated bed. X0 saves result in EEPROM.
- M320 - Activate autolevel
- M321 - Deactivate autolevel
- M322 - Reset autolevel matrix
- M340 P<servoId> S<pulseInUS> : servoID = 0..3, Servos are controlled by a pulse with normally between 500 and 2500 with 1500ms in center position. 0 turns servo off.
- M350 S<mstepsAll> X<mstepsX> Y<mstepsY> Z<mstepsZ> E<mstepsE0> P<mstespE1> : Set microstepping on RAMBO board
- M400 - Wait until move buffers empty.
- M401 - Store x, y and z position.
- M402 - Go to stored position. If X, Y or Z is specified, only these coordinates are used. F changes feedrate fo rthat move.
- M500 Store settings to EEPROM
- M501 Load settings from EEPROM
- M502 Reset settings to the one in configuration.h. Does not store values in EEPROM!
- M908 P<address> S<value> : Set stepper current for digipot (RAMBO board)
*/
]]> Fri, 02 Jan 2015 05:06:32 +0000 https://www.soliforum.com/post/77167/#p77167 <![CDATA[Re: GCode Ref & Reusing XYZ Cartridges]]> https://www.soliforum.com/post/77063/#p77063 carl_m1968 wrote:

I refilled one, and there are a million thongs I would rather spend and hour on.

Heh - there's probably a million thongs I'd rather spend an hour on as well.

Might try the cartridge refill once just to say I did it. Assuming you don't use the carts, do you use an external feeder or do you make use of the available cart space in the printer? I like the idea of keeping it compact - even when I move it into my workroom I don't necessarily want a bunch of spare spools lying around just asking for my kids to mess with them.

carl_m1968 wrote:

The light control was never enabled on the rep firmware as most as far as I know leave it on. being LED the energy it uses it nearly none.

That's just one example though - I'd like to manage ooze, retraction, wipes etc and it would be useful to have some GCode reference.

]]> Wed, 31 Dec 2014 23:05:58 +0000 https://www.soliforum.com/post/77063/#p77063 <![CDATA[Re: GCode Ref & Reusing XYZ Cartridges]]> https://www.soliforum.com/post/77061/#p77061 montressor wrote:

Setup: Davinci Duo with Repetier 0.92 Firmware, Octopi Print Server, Simplify3D Mac

Couple questions:

- Anyone know of a good GCode reference that describes codes available on Repetier 0.92? I know of https://github.com/repetier/Repetier-Fi … i/G-codes, but it seems incomplete (no control of light, no mention of switching current extruder, etc). I also know the default firmware allows for some special XYZ-only commands, not sure if those are still available.

- I hacked together an ugly DIY filament holder until I decide which one to print, but I actually like the idea of cartridges, or at least something that uses that space. Has anyone tried refilling the cartridges with 3rd-party filament? Or know of anyone having tried to use the spool bays?


I refilled one, and there are a million thongs I would rather spend and hour on. Unless you can make rig that will turn the feeding and receiving roll at the same time it is a pain in the asterisk.

The light control was never enabled on the rep firmware as most as far as I know leave it on. being LED the energy it uses it nearly none.

]]> Wed, 31 Dec 2014 23:00:20 +0000 https://www.soliforum.com/post/77061/#p77061 <![CDATA[GCode Ref & Reusing XYZ Cartridges]]> https://www.soliforum.com/post/77059/#p77059 Setup: Davinci Duo with Repetier 0.92 Firmware, Octopi Print Server, Simplify3D Mac

Couple questions:

- Anyone know of a good GCode reference that describes codes available on Repetier 0.92? I know of https://github.com/repetier/Repetier-Fi … i/G-codes, but it seems incomplete (no control of light, no mention of switching current extruder, etc). I also know the default firmware allows for some special XYZ-only commands, not sure if those are still available.

- I hacked together an ugly DIY filament holder until I decide which one to print, but I actually like the idea of cartridges, or at least something that uses that space. Has anyone tried refilling the cartridges with 3rd-party filament? Or know of anyone having tried to use the spool bays?

]]> Wed, 31 Dec 2014 22:16:04 +0000 https://www.soliforum.com/post/77059/#p77059