<![CDATA[SoliForum - 3D Printing Community — Simplify 3D now supports Da Vinci 1.0 and 2.0]]> https://www.soliforum.com/topic/8668/simplify-3d-now-supports-da-vinci-10-and-20/ Sun, 21 Dec 2014 14:00:21 +0000 PunBB <![CDATA[Re: Simplify 3D now supports Da Vinci 1.0 and 2.0]]> https://www.soliforum.com/post/76062/#p76062 pricecg44 wrote:

The printer says its 1.0.3, yet I just updated the firmware? Is the 1.2.3 only for the duo or the aio?

You've probably got one of the very very new printers that has a completely different main board and different/new firmware.

]]> Sun, 21 Dec 2014 14:00:21 +0000 https://www.soliforum.com/post/76062/#p76062 <![CDATA[Re: Simplify 3D now supports Da Vinci 1.0 and 2.0]]> https://www.soliforum.com/post/76060/#p76060 My chief suspect is the speed Is too large. So I'm looking thru the hacking thread on that, cf what simplify outputs. Can we get a text version of the gcode output? The output of simplify is 'factory' format that is binary.

]]> Sun, 21 Dec 2014 10:15:40 +0000 https://www.soliforum.com/post/76060/#p76060 <![CDATA[Re: Simplify 3D now supports Da Vinci 1.0 and 2.0]]> https://www.soliforum.com/post/76059/#p76059 I am getting the same crap prints for several small rubber gun bit stl's loaded together.
The larger piece  just a 3cm gear type thingy.

Can someone post their successful simplify parameters (including the dialog it is in) please.

]]> Sun, 21 Dec 2014 10:07:57 +0000 https://www.soliforum.com/post/76059/#p76059 <![CDATA[Re: Simplify 3D now supports Da Vinci 1.0 and 2.0]]> https://www.soliforum.com/post/76058/#p76058 The printer says its 1.0.3, yet I just updated the firmware? Is the 1.2.3 only for the duo or the aio?

]]> Sun, 21 Dec 2014 10:01:48 +0000 https://www.soliforum.com/post/76058/#p76058 <![CDATA[Re: Simplify 3D now supports Da Vinci 1.0 and 2.0]]> https://www.soliforum.com/post/76048/#p76048 pricecg44 wrote:
georgehine wrote:

what firmware are you running on your da vinci? I am under the impression that it doesnt work with the new firmwares version 1.0.1 and up.


I've just updated the firmware, I can send a Gcode from simplify to the da Vinci, just have to get
It right.

make sure your not running 1.2.3 firmware as it says the software will only work with all firmwares before the 1.2.3

]]> Sun, 21 Dec 2014 05:39:46 +0000 https://www.soliforum.com/post/76048/#p76048 <![CDATA[Re: Simplify 3D now supports Da Vinci 1.0 and 2.0]]> https://www.soliforum.com/post/76029/#p76029 carl_m1968 wrote:
pricecg44 wrote:

Ok, the print job was cancelled, messy.  Before I experiment, has anyone done working adjustments to temps, speeds etc.

Speeds for this printer should be 40 or less. Temps on average should be 210 for extruder and 90 to 110 for bed..


The speed set under the fff dialog was 1800mm/min, will try 1000. Extruded temp wa 220, will try 212 as per normal operation.

The use of simplify really is a 'no choicer' such as stuff like putting all those single piece stl's together.

]]> Sun, 21 Dec 2014 01:42:54 +0000 https://www.soliforum.com/post/76029/#p76029 <![CDATA[Re: Simplify 3D now supports Da Vinci 1.0 and 2.0]]> https://www.soliforum.com/post/76028/#p76028 georgehine wrote:

what firmware are you running on your da vinci? I am under the impression that it doesnt work with the new firmwares version 1.0.1 and up.


I've just updated the firmware, I can send a Gcode from simplify to the da Vinci, just have to get
It right.

]]> Sun, 21 Dec 2014 01:37:49 +0000 https://www.soliforum.com/post/76028/#p76028 <![CDATA[Re: Simplify 3D now supports Da Vinci 1.0 and 2.0]]> https://www.soliforum.com/post/76019/#p76019 pricecg44 wrote:

Just got simplify, great stuff except it will not connect with my da dinci 1.0.
I've tried com3 and com1 with all the baud rates. Also I turned the printer on/off as that solves the busy printer error in xyzware.

what firmware are you running on your da vinci? I am under the impression that it doesnt work with the new firmwares version 1.0.1 and up.

]]> Sat, 20 Dec 2014 23:44:20 +0000 https://www.soliforum.com/post/76019/#p76019 <![CDATA[Re: Simplify 3D now supports Da Vinci 1.0 and 2.0]]> https://www.soliforum.com/post/76016/#p76016 pricecg44 wrote:

Ok, the print job was cancelled, messy.  Before I experiment, has anyone done working adjustments to temps, speeds etc.

Speeds for this printer should be 40 or less. Temps on average should be 210 for extruder and 90 to 110 for bed..

]]> Sat, 20 Dec 2014 23:36:50 +0000 https://www.soliforum.com/post/76016/#p76016 <![CDATA[Re: Simplify 3D now supports Da Vinci 1.0 and 2.0]]> https://www.soliforum.com/post/76014/#p76014 Ok, the print job was cancelled, messy.  Before I experiment, has anyone done working adjustments to temps, speeds etc.

]]> Sat, 20 Dec 2014 23:18:37 +0000 https://www.soliforum.com/post/76014/#p76014 <![CDATA[Re: Simplify 3D now supports Da Vinci 1.0 and 2.0]]> https://www.soliforum.com/post/76011/#p76011 Ah got it to talk. Just off/on'ed the printer then Quickly hit the connect button in the machine dialog box. Could be a hit and miss thing.
Warming up ....

]]> Sat, 20 Dec 2014 22:42:32 +0000 https://www.soliforum.com/post/76011/#p76011 <![CDATA[Re: Simplify 3D now supports Da Vinci 1.0 and 2.0]]> https://www.soliforum.com/post/76006/#p76006 Just got simplify, great stuff except it will not connect with my da dinci 1.0.
I've tried com3 and com1 with all the baud rates. Also I turned the printer on/off as that solves the busy printer error in xyzware.

]]> Sat, 20 Dec 2014 22:28:21 +0000 https://www.soliforum.com/post/76006/#p76006 <![CDATA[Re: Simplify 3D now supports Da Vinci 1.0 and 2.0]]> https://www.soliforum.com/post/75060/#p75060 I just got S3d last night so I have not had a lot of time to play with it yet. What I have played with so far is great. I love the option of setting the temps at different layers. I can now start to cool the bed down as the print get close to the end.

]]> Sat, 13 Dec 2014 15:05:43 +0000 https://www.soliforum.com/post/75060/#p75060 <![CDATA[Re: Simplify 3D now supports Da Vinci 1.0 and 2.0]]> https://www.soliforum.com/post/75026/#p75026 of course the print quality is better just look at all the features you get with the software. you also get a simulation to review with s3d. with full control over your printing capability it kicks the crap out of the xyzware . xyzware only gives you a couple options and you are stuck with what ever it gives you but the s3d allows so much adjustability you can actually cut your print times by a lot compared to the xyzware. and you don't have xyz able to remotely access your printer and take control of your property and lock you out of being able to run it open source.

]]> Sat, 13 Dec 2014 03:29:48 +0000 https://www.soliforum.com/post/75026/#p75026 <![CDATA[Re: Simplify 3D now supports Da Vinci 1.0 and 2.0]]> https://www.soliforum.com/post/74985/#p74985 BlueTape wrote:

Here it is folks, i brought my laptop over to my friend's place and he has a 2.0 with stock firmware:

Looks good. Do you think the quality is better than using XYZWare?

]]> Fri, 12 Dec 2014 20:26:16 +0000 https://www.soliforum.com/post/74985/#p74985