<![CDATA[SoliForum - 3D Printing Community — Problem with the temperature not stopping or stabilizing]]> https://www.soliforum.com/topic/8503/problem-with-the-temperature-not-stopping-or-stabilizing/ Sat, 29 Nov 2014 00:27:11 +0000 PunBB <![CDATA[Re: Problem with the temperature not stopping or stabilizing]]> https://www.soliforum.com/post/73378/#p73378 No problem, we've all been there!

PLA is generally 160-170C
ABS is generally 180-190C

But there are many types of PLA and many types of ABS, so it takes some experimentation for each grade.

Quite a bit of PLA extrusion here:

http://www.soliforum.com/topic/7470/pla-4043d/

Be sure to check out the two guides linked in the last post of that thread. Pre drying and increased cooling are important.

]]> Sat, 29 Nov 2014 00:27:11 +0000 https://www.soliforum.com/post/73378/#p73378 <![CDATA[Re: Problem with the temperature not stopping or stabilizing]]> https://www.soliforum.com/post/73368/#p73368 Ok, that was so stupid -.-

I think the problem was exactly that, somehow the "." disapeared and the temperature was set to 1900...
Now the temperature is working fine, will have to try the machine tomorrow to see if I can get any good results this time around, what temperature you sugest to try? for PLA and for ABS

Thank you again for your help big_smile

]]> Fri, 28 Nov 2014 22:38:31 +0000 https://www.soliforum.com/post/73368/#p73368 <![CDATA[Re: Problem with the temperature not stopping or stabilizing]]> https://www.soliforum.com/post/73364/#p73364 I just noticed something - you seem to have the controller set to 1900C, not 190.0C!!

Try setting it to 190.0C.

As for the temperature dropping, can you post a photo of the nozzle area?

]]> Fri, 28 Nov 2014 22:09:30 +0000 https://www.soliforum.com/post/73364/#p73364 <![CDATA[Re: Problem with the temperature not stopping or stabilizing]]> https://www.soliforum.com/post/73363/#p73363 It would be marked as replacement parts/gift with no value, so there shouldn't be taxes. Since you're international, no need to send it back.

Not sure where they're sold in Europe.

Regarding filament diameter - being able to set the temperature accurately will help. Have you predried the PLA?

Can you confirm the temperature using another probe, to see if it matches?

Can you stop the fan from spinning, and report what the temperature does?

]]> Fri, 28 Nov 2014 22:07:57 +0000 https://www.soliforum.com/post/73363/#p73363 <![CDATA[Re: Problem with the temperature not stopping or stabilizing]]> https://www.soliforum.com/post/73362/#p73362 Im from portugal so the taxes would be insane to send it and receive the other one.
Is there any place in europe I can buy those from, Im sure it would be cheaper then to swap it.

I payed around 130$ in taxes to receive the filastruder kit :\

I hope I can get it working without having to receive another, although Im thinkin in getting the filawinder cause I cant get the right diameter with the filament droping down to the floor

Im going to try something else, I dont know really :s

]]> Fri, 28 Nov 2014 22:01:31 +0000 https://www.soliforum.com/post/73362/#p73362 <![CDATA[Re: Problem with the temperature not stopping or stabilizing]]> https://www.soliforum.com/post/73357/#p73357 Very strange - I haven't run into anything like this before. Lets try swapping out the controller and thermocouple - use the contact form on the Filastruder site and we'll get an exchange set up.

]]> Fri, 28 Nov 2014 21:35:29 +0000 https://www.soliforum.com/post/73357/#p73357 <![CDATA[Re: Problem with the temperature not stopping or stabilizing]]> https://www.soliforum.com/post/73356/#p73356 Sorry, forgot to answer those, temperature is around 18º I think, yes, its the cooling fan that came with the kit (should the blowing be directing at the filament, (sticker side up), or down(sticker side down)??) although allready tried both ways and same thing happens, but before I turned it blowing to the filament, the temperature just kept going up, when I pput the fan blowing at fillament, the temperature goes down...

Not sure what you mean about the thermistor, its mounted like it said in the instructions, I can take a pic if you want

the settings are the default values, Ive checked just now

]]> Fri, 28 Nov 2014 21:33:02 +0000 https://www.soliforum.com/post/73356/#p73356 <![CDATA[Re: Problem with the temperature not stopping or stabilizing]]> https://www.soliforum.com/post/73345/#p73345 Hmm. I wonder if it is set to cooling instead of heating. Can you confirm the settings in the controller match the factory settings by scrolling through them and comparing to the manual?

Also, answers to these questions:

Are you using the included cooling fan? What are the ambient temperatures? How is the thermistor mounted?

Would help.

]]> Fri, 28 Nov 2014 20:46:10 +0000 https://www.soliforum.com/post/73345/#p73345 <![CDATA[Re: Problem with the temperature not stopping or stabilizing]]> https://www.soliforum.com/post/73340/#p73340 Hi again

Yes, the OUT led is lit up


Its working like this, I put the value 190º it goes up to 230º for example, and to not let it go any further I turn ON the motor, after the motor is running the temperature starts to come down, then stablizes at around 165º like you saw in the photo

The OUT led is allways on, never seen it off

Hope this helps

]]> Fri, 28 Nov 2014 20:21:05 +0000 https://www.soliforum.com/post/73340/#p73340 <![CDATA[Re: Problem with the temperature not stopping or stabilizing]]> https://www.soliforum.com/post/73329/#p73329 Back at a computer now.

Are you using the included cooling fan? What are the ambient temperatures? How is the thermocouple mounted?

When it is several degrees above the setpoint, is the OUT LED lit up?

This is odd, but we'll figure it out!

]]> Fri, 28 Nov 2014 16:57:00 +0000 https://www.soliforum.com/post/73329/#p73329 <![CDATA[Re: Problem with the temperature not stopping or stabilizing]]> https://www.soliforum.com/post/73314/#p73314 No, Im extruding PLA

And thank you for your help btw, if you need more photos or something let me know

]]> Fri, 28 Nov 2014 12:19:14 +0000 https://www.soliforum.com/post/73314/#p73314 <![CDATA[Re: Problem with the temperature not stopping or stabilizing]]> https://www.soliforum.com/post/73313/#p73313 That is far too cool for ABS. I hope you're not extruding ABS!

About to get on a plane, will respond more soon.

]]> Fri, 28 Nov 2014 11:22:02 +0000 https://www.soliforum.com/post/73313/#p73313 <![CDATA[Re: Problem with the temperature not stopping or stabilizing]]> https://www.soliforum.com/post/73312/#p73312 You got it

Also attatched a photo of the filastruder after running for 1 hour, it stabilizes at this temperatures

]]> Fri, 28 Nov 2014 10:42:23 +0000 https://www.soliforum.com/post/73312/#p73312 <![CDATA[Re: Problem with the temperature not stopping or stabilizing]]> https://www.soliforum.com/post/73310/#p73310 Sounds like it is not wired correctly. How about a photo of the back of the controller?

]]> Fri, 28 Nov 2014 10:23:15 +0000 https://www.soliforum.com/post/73310/#p73310 <![CDATA[Problem with the temperature not stopping or stabilizing]]> https://www.soliforum.com/post/73308/#p73308 Hi there comunity, not sure if this is the right place to post this

I have finished assembling my filastruder but wasnt able to make it work still

When I turn it on with the auto tune on, I put the temperature on 190º for example, it starts to go up, then keep heating, I have just turned it on and its allready on 230º

Is this normal?

And when I turn the motor on, the temperature starts to come down, but never to the 190º

The temperature never stabilizes, and never is the same on PV and SV

Also, what temperature you use for pla and what you use for ABS?

Thank you so much for your help

Love the filastruder xD

]]> Fri, 28 Nov 2014 10:02:43 +0000 https://www.soliforum.com/post/73308/#p73308