SoliForum - 3D Printing Community — SD4 strange vertical sides, not straigh lines, almost wicker basketish

Re: SD4 strange vertical sides, not straigh lines, almost wicker basketish

null@example.com (IanJohnson) — Mon, 20 Oct 2014 21:33:34 +0000

You can listen for it better if you turn the manual extrusion speed way down in Repetier to something like 5. The motor will turn so slowly that you can hear the pulsing of the microsteps. Then turn the vref back and forth and listen for the spot where it sounds the smoothest.

Re: SD4 strange vertical sides, not straigh lines, almost wicker basketish

null@example.com (saqueeb) — Mon, 20 Oct 2014 21:32:35 +0000

ggunners wrote:

You still have a periodic repetition there. It is much better than before.

would you suggest adjusting it even more?

Re: SD4 strange vertical sides, not straigh lines, almost wicker basketish

null@example.com (ggunners) — Mon, 20 Oct 2014 21:02:33 +0000

You still have a periodic repetition there. It is much better than before.

Re: SD4 strange vertical sides, not straigh lines, almost wicker basketish

null@example.com (wardjr) — Sat, 18 Oct 2014 04:47:51 +0000

saqueeb wrote:

AZERATE wrote:
Yup...non conductive is your friend here.
VREF adjustments are typically done by hearing. There is a sweet spot in between a struggling and whining noise. Most people start low then work their way up. This will be done while printing a test.
You can also adjust it via voltmeter, but I couldn't walk you through that step personally.
yep that was it!
quarter turn CCW fixed it! thank you very much!

A 1/4 turn? Holy crap that thing was way out of adjustment.

Re: SD4 strange vertical sides, not straigh lines, almost wicker basketish

null@example.com (saqueeb) — Sat, 18 Oct 2014 02:15:12 +0000

AZERATE wrote:

Yup...non conductive is your friend here.
VREF adjustments are typically done by hearing. There is a sweet spot in between a struggling and whining noise. Most people start low then work their way up. This will be done while printing a test.
You can also adjust it via voltmeter, but I couldn't walk you through that step personally.

yep that was it!

quarter turn CCW fixed it! thank you very much!

Re: SD4 strange vertical sides, not straigh lines, almost wicker basketish

null@example.com (AZERATE) — Sat, 18 Oct 2014 02:01:44 +0000

Yup...non conductive is your friend here.
VREF adjustments are typically done by hearing. There is a sweet spot in between a struggling and whining noise. Most people start low then work their way up. This will be done while printing a test.

You can also adjust it via voltmeter, but I couldn't walk you through that step personally.

Re: SD4 strange vertical sides, not straigh lines, almost wicker basketish

null@example.com (saqueeb) — Sat, 18 Oct 2014 01:53:29 +0000

so basically just a non conductive screwdriver? ( plastic, etc) clockwise? CCW? or just try each and see?

Re: SD4 strange vertical sides, not straigh lines, almost wicker basketish

null@example.com (AZERATE) — Sat, 18 Oct 2014 01:40:24 +0000

My vote is moire.
Use a ceramic screwdriver to adjust the E VREF on the board. When you do this, turn it ever so slightly. The tiniest adjustment will have a significant effect.

SD4 strange vertical sides, not straigh lines, almost wicker basketish

null@example.com (saqueeb) — Sat, 18 Oct 2014 01:36:47 +0000

my SD4 with E3DV6 is now printing strange vertical walls, no longer do i get straight lines on any side wall now they are wavy? checkerboard? wicker looking? please see pics and let me know if you have any ideas?

only thing i changed was standard hot end to the E3DV6. with the standard hotend i was getting straight lines, now i get this?

Pics 1, 2, and 4 are from E3DV6

Pic 3 is from original SD4 hotend

Thanks