<![CDATA[SoliForum - 3D Printing Community — Electrical help]]> https://www.soliforum.com/topic/7965/electrical-help/ Sun, 12 Oct 2014 00:44:29 +0000 PunBB <![CDATA[Re: Electrical help]]> https://www.soliforum.com/post/68398/#p68398 I wasn't going to go there, but.............

]]> Sun, 12 Oct 2014 00:44:29 +0000 https://www.soliforum.com/post/68398/#p68398 <![CDATA[Re: Electrical help]]> https://www.soliforum.com/post/68388/#p68388 There's no photo attached.

There's two terminals for the thermocouple on the PID unit, they should be labeled as such. Pins 7 and 8 on the Mypin controller, mind the polarity though.

I'm confused though - if you have an assembled unit, wasn't the thermocouple connector already installed? If you're asking because you disassembled it, then why not just put it back where you found it?

]]> Sat, 11 Oct 2014 21:14:22 +0000 https://www.soliforum.com/post/68388/#p68388 <![CDATA[Re: Electrical help]]> https://www.soliforum.com/post/68385/#p68385 There we go.

]]> Sat, 11 Oct 2014 20:26:01 +0000 https://www.soliforum.com/post/68385/#p68385 <![CDATA[Re: Electrical help]]> https://www.soliforum.com/post/68384/#p68384 https://outlook.office365.com/owa/service.svc/s/GetFileAttachment?id=AAMkADdmYWViNDk3LTBiY2UtNDFiMy1iYTk4LWMzYzlkYjUxNjhlMgBGAAAAAACFy0pK7z%2F8R4LV%2BVfrTw2lBwD9OoNIRBgpQ5BsH3adCUxIAAAAAAENAAD9OoNIRBgpQ5BsH3adCUxIAADFKJ4CAAABEgAQAI4CGJhjqI1IsNgWfpYXLZo%3D&amp;X-OWA-CANARY=2v8hFeWcIEKmu8ScODAaKxPQBn-ks9EIojiVT_qHatiN1ZJrzN6Jk1Q7JK-LX4bmfnN13YkJNEA.

]]> Sat, 11 Oct 2014 20:25:41 +0000 https://www.soliforum.com/post/68384/#p68384 <![CDATA[Re: Electrical help]]> https://www.soliforum.com/post/68383/#p68383 .

]]> Sat, 11 Oct 2014 20:25:06 +0000 https://www.soliforum.com/post/68383/#p68383 <![CDATA[Re: Electrical help]]> https://www.soliforum.com/post/68381/#p68381 I have a pre-assembled kickstarter unit so it is a little bit different than the current manual. It has two pins that cannot be screwed into the terminals. Maybe I need to have so many posts to post a photo.

]]> Sat, 11 Oct 2014 20:16:42 +0000 https://www.soliforum.com/post/68381/#p68381 <![CDATA[Re: Electrical help]]> https://www.soliforum.com/post/68379/#p68379 Looking at the PID diagram it would appear to be Pin 3 & 4.  Look on page 9 of 11.

]]> Sat, 11 Oct 2014 20:10:19 +0000 https://www.soliforum.com/post/68379/#p68379 <![CDATA[Re: Electrical help]]> https://www.soliforum.com/post/68377/#p68377 I guess I can't get it to upload. It's the wire for thermister. I don't remember where it plugs into and cannot find any place that it fits.

]]> Sat, 11 Oct 2014 20:04:33 +0000 https://www.soliforum.com/post/68377/#p68377 <![CDATA[Re: Electrical help]]> https://www.soliforum.com/post/68376/#p68376 Yes. I'll try it again.

]]> Sat, 11 Oct 2014 20:01:10 +0000 https://www.soliforum.com/post/68376/#p68376 <![CDATA[Re: Electrical help]]> https://www.soliforum.com/post/68375/#p68375 Did you intend to attach an image?

]]> Sat, 11 Oct 2014 19:51:03 +0000 https://www.soliforum.com/post/68375/#p68375 <![CDATA[Electrical help]]> https://www.soliforum.com/post/68374/#p68374 Where does this yellow plug in go?

]]> Sat, 11 Oct 2014 19:47:19 +0000 https://www.soliforum.com/post/68374/#p68374