<![CDATA[SoliForum - 3D Printing Community — New LCD]]> https://www.soliforum.com/topic/796/new-lcd/ Mon, 21 Oct 2013 18:15:37 +0000 PunBB <![CDATA[Re: New LCD]]> https://www.soliforum.com/post/39525/#p39525 ErroneousBosch wrote:

Rip, can you list what changes you made to the firmware?

This up and working? We may stock a LCD someday.

]]> Mon, 21 Oct 2013 18:15:37 +0000 https://www.soliforum.com/post/39525/#p39525 <![CDATA[Re: New LCD]]> https://www.soliforum.com/post/38756/#p38756 Rip, can you list what changes you made to the firmware?

]]> Sat, 12 Oct 2013 17:18:50 +0000 https://www.soliforum.com/post/38756/#p38756 <![CDATA[Re: New LCD]]> https://www.soliforum.com/post/36415/#p36415 rjp350z wrote:
rjp350z wrote:

I know it’s been a while but going to resurrect this old thread….

Was finally able to the my VIKI working on my SD3.  I still have a lot of testing and cleanup of the code but all seems to be functioning now.

The biggest hurdle I hit was not being able to get the VIKI SD card to function.  After MUCH, MUCH reading and research I finally figured out that the #define SDSS in the pins.h file was set to 31 when it needs to be set to 37 for the VIKI to work correctly.

The up, down and left buttons still need some work but the rotary wheel and select button work fine for now.

Attached is copy of the lawsy’s updated firmware.  Once I confirm working 100% and cleaned up I will submit merge request on GITHUB.

IMPORTANT:  PLEASE USE AT YOUR OWN RISK.  Firmware is setup for SD3 with E3D hotend so make sure you edit before uploading and it is only confirmed working with Sanguinololu board.

Pin outs used are below

Viki pins----Description---------------Sanguinololu
+5V--------+ 5V input----------------EXT/+5V
GND--------Power supply Ground----ETX/GND
SDA--------i2C SDA-------------------SDA (Digital Pin 17)
SCL--------i2C SCL--------------------SCL (Digital Pin 16)
ENC_A-----Rotary Encoder pin A-----D10
ENC_B-----Rotary Encoder pin B-----D11
         
CS----------SD chip select------------A3/D31
BTN--------Push Button switch pin--USER PREF. (A1/D30)
DI----------SD Data input------------ICSP/MOSI
CLK--------SD Clock------------------ICSP/SCK
CD---------SD Card detect pin-------Any Digital pin (A2/D29)
DO---------SD Data output----------ICSP/MISO
        
Jumper J4, J6=SHORTED

Forgot to mention,  In the picture is shows "Mendel Ready".  That was also fixed but didn't have an updated picture yet.  It now shows" SOLIDOODLE 3 Ready." wink

I changed mine to be 2n2r5Bot ... a little narcissistic i know. tongue

]]> Sun, 15 Sep 2013 18:01:09 +0000 https://www.soliforum.com/post/36415/#p36415 <![CDATA[Re: New LCD]]> https://www.soliforum.com/post/36413/#p36413 rjp350z wrote:

I know it’s been a while but going to resurrect this old thread….

Was finally able to the my VIKI working on my SD3.  I still have a lot of testing and cleanup of the code but all seems to be functioning now.

The biggest hurdle I hit was not being able to get the VIKI SD card to function.  After MUCH, MUCH reading and research I finally figured out that the #define SDSS in the pins.h file was set to 31 when it needs to be set to 37 for the VIKI to work correctly.

The up, down and left buttons still need some work but the rotary wheel and select button work fine for now.

Attached is copy of the lawsy’s updated firmware.  Once I confirm working 100% and cleaned up I will submit merge request on GITHUB.

IMPORTANT:  PLEASE USE AT YOUR OWN RISK.  Firmware is setup for SD3 with E3D hotend so make sure you edit before uploading and it is only confirmed working with Sanguinololu board.

Pin outs used are below

Viki pins----Description---------------Sanguinololu
+5V--------+ 5V input----------------EXT/+5V
GND--------Power supply Ground----ETX/GND
SDA--------i2C SDA-------------------SDA (Digital Pin 17)
SCL--------i2C SCL--------------------SCL (Digital Pin 16)
ENC_A-----Rotary Encoder pin A-----D10
ENC_B-----Rotary Encoder pin B-----D11
         
CS----------SD chip select------------A3/D31
BTN--------Push Button switch pin--USER PREF. (A1/D30)
DI----------SD Data input------------ICSP/MOSI
CLK--------SD Clock------------------ICSP/SCK
CD---------SD Card detect pin-------Any Digital pin (A2/D29)
DO---------SD Data output----------ICSP/MISO
        
Jumper J4, J6=SHORTED

Forgot to mention,  In the picture is shows "Mendel Ready".  That was also fixed but didn't have an updated picture yet.  It now shows" SOLIDOODLE 3 Ready." wink

]]> Sun, 15 Sep 2013 17:43:17 +0000 https://www.soliforum.com/post/36413/#p36413 <![CDATA[Re: New LCD]]> https://www.soliforum.com/post/36411/#p36411 I know it’s been a while but going to resurrect this old thread….

Was finally able to the my VIKI working on my SD3.  I still have a lot of testing and cleanup of the code but all seems to be functioning now.

The biggest hurdle I hit was not being able to get the VIKI SD card to function.  After MUCH, MUCH reading and research I finally figured out that the #define SDSS in the pins.h file was set to 31 when it needs to be set to 37 for the VIKI to work correctly.

The up, down and left buttons still need some work but the rotary wheel and select button work fine for now.

Attached is copy of the lawsy’s updated firmware.  Once I confirm working 100% and cleaned up I will submit merge request on GITHUB.

IMPORTANT:  PLEASE USE AT YOUR OWN RISK.  Firmware is setup for SD3 with E3D hotend so make sure you edit before uploading and it is only confirmed working with Sanguinololu board.

Pin outs used are below

Viki pins----Description---------------Sanguinololu
+5V--------+ 5V input----------------EXT/+5V
GND--------Power supply Ground----ETX/GND
SDA--------i2C SDA-------------------SDA (Digital Pin 17)
SCL--------i2C SCL--------------------SCL (Digital Pin 16)
ENC_A-----Rotary Encoder pin A-----D10
ENC_B-----Rotary Encoder pin B-----D11
         
CS----------SD chip select------------A3/D31
BTN--------Push Button switch pin--USER PREF. (A1/D30)
DI----------SD Data input------------ICSP/MOSI
CLK--------SD Clock------------------ICSP/SCK
CD---------SD Card detect pin-------Any Digital pin (A2/D29)
DO---------SD Data output----------ICSP/MISO
        
Jumper J4, J6=SHORTED

]]> Sun, 15 Sep 2013 17:40:48 +0000 https://www.soliforum.com/post/36411/#p36411 <![CDATA[Re: New LCD]]> https://www.soliforum.com/post/30573/#p30573 +1

]]> Mon, 22 Jul 2013 12:06:40 +0000 https://www.soliforum.com/post/30573/#p30573 <![CDATA[Re: New LCD]]> https://www.soliforum.com/post/30272/#p30272 I can't believe I rushed out to get one of these LCDs.
On the plus side it's been making a great paperweight.

]]> Fri, 19 Jul 2013 08:07:54 +0000 https://www.soliforum.com/post/30272/#p30272 <![CDATA[Re: New LCD]]> https://www.soliforum.com/post/30030/#p30030 Sigh, it's the missing link in my awesome case build that I want to share with the world, but wanted to wait for its completion.

]]> Tue, 16 Jul 2013 19:22:58 +0000 https://www.soliforum.com/post/30030/#p30030 <![CDATA[Re: New LCD]]> https://www.soliforum.com/post/30028/#p30028 I want to believe this will all happen  but...

]]> Tue, 16 Jul 2013 18:53:48 +0000 https://www.soliforum.com/post/30028/#p30028 <![CDATA[Re: New LCD]]> https://www.soliforum.com/post/29788/#p29788 Unfortunately no,  Haven't had much time lately to work on it.   Work has been exceptionally busy the past few weeks

]]> Sat, 13 Jul 2013 22:58:57 +0000 https://www.soliforum.com/post/29788/#p29788 <![CDATA[Re: New LCD]]> https://www.soliforum.com/post/29762/#p29762 So I hate to ask, but has anyone got this up and running on their Solidoodle or should I just forget it?

]]> Sat, 13 Jul 2013 17:29:01 +0000 https://www.soliforum.com/post/29762/#p29762 <![CDATA[Re: New LCD]]> https://www.soliforum.com/post/22940/#p22940 Vimeo is still converting the videos.  Should be up in about 30 minutes.

rjp350z wrote:

Here are two short videos.  I tested both Lincomatic and Lawsys on a fully populated arduino and still get the same results.

As you can see Lincomaic seems to work fine but with my semi working worsion on Lawsy version I seem to be getting a constant refresh or some sort of loop that I still need to work out.

Attached is the Lawsy version I've been working with if anyone wants to take a look and possibly shed some light on what I might be missing.

Lincomatic
https://vimeo.com/66282370

Lawsy
https://vimeo.com/66282290

]]> Wed, 15 May 2013 22:57:34 +0000 https://www.soliforum.com/post/22940/#p22940 <![CDATA[Re: New LCD]]> https://www.soliforum.com/post/22939/#p22939 Here are two short videos.  I tested both Lincomatic and Lawsys on a fully populated arduino and still get the same results.

As you can see Lincomaic seems to work fine but with my semi working worsion on Lawsy version I seem to be getting a constant refresh or some sort of loop that I still need to work out.

Attached is the Lawsy version I've been working with if anyone wants to take a look and possibly shed some light on what I might be missing.

Lincomatic
https://vimeo.com/66282370

Lawsy
https://vimeo.com/66282290

]]> Wed, 15 May 2013 22:56:18 +0000 https://www.soliforum.com/post/22939/#p22939 <![CDATA[Re: New LCD]]> https://www.soliforum.com/post/22887/#p22887 I got a shipping notification also with mine but status never updated just showed up one day. About a week later

Thanks USPS wink

]]> Wed, 15 May 2013 16:25:07 +0000 https://www.soliforum.com/post/22887/#p22887 <![CDATA[Re: New LCD]]> https://www.soliforum.com/post/22879/#p22879 Im still waiting on my Viki! Got a ship notification on 4/30/13 and the tracking number still says it never even got picked up from roy. whats that 2 weeks??

Smitty sad

]]> Wed, 15 May 2013 14:39:58 +0000 https://www.soliforum.com/post/22879/#p22879