SoliForum - 3D Printing Community — White Powder Buildup - Right Y-Axis

Re: White Powder Buildup - Right Y-Axis

null@example.com (nickythegreek) — Sat, 15 Dec 2012 01:12:22 +0000

Thanks for the suggestion joosh.

Some 600 grit sandpaper solved this problem in under 2 minutes (already placed in order for a replacement rod from the solidoodle shop though). I have done 3 prints since buffing it down and the bar has been completely free of teflon dust. I'll rotate the teflon block to the other side later tonight; which looks like it will actually make both blocks hug the rod finally. This should help me really dial in these print settings!

Re: White Powder Buildup - Right Y-Axis

null@example.com (nickythegreek) — Fri, 14 Dec 2012 13:25:53 +0000

Does your bottom and top teflon both touch the rod? My bottom teflon block has always had to much clearance.

Re: White Powder Buildup - Right Y-Axis

null@example.com (jooshs) — Fri, 14 Dec 2012 05:08:48 +0000

You should be able to buffer that out with progressively higher grit sand papers. It is tough to tell how deep the scratches are but you don't want to change the dimensions or roundness of the rod either. Maybe you can just turn it so that the scratches don't come into contact with the Teflon on top or bottom. Either way, you should still flip the Teflon or get a new block. Also make sure there is nothing on your carriage that might be scratching the rod.

Re: White Powder Buildup - Right Y-Axis

null@example.com (nickythegreek) — Fri, 14 Dec 2012 02:27:39 +0000

Yep... The Y-Axis rod starts off with a big gouge, which then becomes a pair of gouges and afterwords is full of tiny dings and dents as I run my fingernail over it. Left rod is smooth and greasy. Solidoodle should be checking these rods post-installation for this sort of thing before shipping em off.

Re: White Powder Buildup - Right Y-Axis

null@example.com (NG) — Fri, 14 Dec 2012 02:19:24 +0000

nickythegreek wrote:

Yep, pile at the other end as well. I've had powder on the rod since day one so I never suspected it was an issue until I saw the large pile today, no way it should be wearing that quickly! I'll inspect the rod for sticky debris after current print, thanks for the suggestion.

If you don't mind I just wondered how long you have had this printer ?

Re: White Powder Buildup - Right Y-Axis

null@example.com (nickythegreek) — Fri, 14 Dec 2012 01:46:33 +0000

Yep, pile at the other end as well. I've had powder on the rod since day one so I never suspected it was an issue until I saw the large pile today, no way it should be wearing that quickly! I'll inspect the rod for sticky debris after current print, thanks for the suggestion.

Re: White Powder Buildup - Right Y-Axis

null@example.com (jooshs) — Fri, 14 Dec 2012 00:35:45 +0000

You should inspect the rod very closely for a bit of superglue or abs that may be stuck on it somewhere. I wouldn't say long term damage, but I would flip the Teflon block over if it is drilled so the hole is centered. If not, I would get a new one to replace that since you can see a groove has been carved. I'm not sure but don't think it could be a greasing issue since enough friction to shred the Teflon would make the motors skip. I would think it is more likely there is an actually sharp chunk of impedance. Is that another pile down on the other end of the rod too?

White Powder Buildup - Right Y-Axis

null@example.com (nickythegreek) — Thu, 13 Dec 2012 23:40:43 +0000

This can't be good..

I assume I need lithium grease to stop this? Is there any long term damage or adjustments I should make now? I didn't expect to need to grease so soon.