<![CDATA[SoliForum - 3D Printing Community — 'struder noob Beta unit build. Problem solving etc etc]]> https://www.soliforum.com/topic/7548/struder-noob-beta-unit-build-problem-solving-etc-etc/ Sat, 06 Sep 2014 14:36:06 +0000 PunBB <![CDATA[Re: 'struder noob Beta unit build. Problem solving etc etc]]> https://www.soliforum.com/post/65592/#p65592 I got a jewelers drill set from amazon. It came with drill bits from 1-2mm in .1mm intervals.

]]> Sat, 06 Sep 2014 14:36:06 +0000 https://www.soliforum.com/post/65592/#p65592 <![CDATA[Re: 'struder noob Beta unit build. Problem solving etc etc]]> https://www.soliforum.com/post/65568/#p65568 wardjr wrote:

I knew I saw a filawinder in your future wink

My laziness knows no bounds tongue


None of the hardware stores within reasonable distance stocks 1.7 or 1.8mm drill bits.... Surprise surprise....

]]> Sat, 06 Sep 2014 05:43:02 +0000 https://www.soliforum.com/post/65568/#p65568 <![CDATA[Re: 'struder noob Beta unit build. Problem solving etc etc]]> https://www.soliforum.com/post/65461/#p65461 I knew I saw a filawinder in your future wink

]]> Fri, 05 Sep 2014 01:21:13 +0000 https://www.soliforum.com/post/65461/#p65461 <![CDATA[Re: 'struder noob Beta unit build. Problem solving etc etc]]> https://www.soliforum.com/post/65445/#p65445 Ah, okie dokie then.
Off to bunnings I go tomorrow for drill bits.

I know it can be run with the original wood, I guess it's just my paranoia that says metal would be more logical.
Either way I've still got a Filawinder to order and setup so that's all way ahead of me anyway.

]]> Thu, 04 Sep 2014 23:37:07 +0000 https://www.soliforum.com/post/65445/#p65445 <![CDATA[Re: 'struder noob Beta unit build. Problem solving etc etc]]> https://www.soliforum.com/post/65353/#p65353 1.3 probably won't feed well. You can drill the hole with a hand drill, no need for a drill press.

Folks have used extrusion:

http://imgur.com/a/GaaBt#0

I have over 1800 hours on a wooden base, horizontal unit though.

]]> Thu, 04 Sep 2014 15:05:21 +0000 https://www.soliforum.com/post/65353/#p65353 <![CDATA[Re: 'struder noob Beta unit build. Problem solving etc etc]]> https://www.soliforum.com/post/65336/#p65336 Looks like the lube did the job! big_smile No more evil noises since I applied it about 2 hours ago.
Thanks for the quick responses, Tim, I'd be lost in a sea of unknown mechanical terms without you tongue

Here's another clip for proof of life.
https://www.youtube.com/watch?v=m9SIwMXiL0U

Do you think I'd be able to print with 1.3mm filament? Or would it be best to stop making the stuff and find someone who can drill out the hole for me?
The other thing I'm curious about is swapping the wood for some form of extrusion like mitsumi or something.
I was a guitar nerd for long enough to realise just how damned annoying wood can be.

]]> Thu, 04 Sep 2014 07:38:29 +0000 https://www.soliforum.com/post/65336/#p65336 <![CDATA[Re: 'struder noob Beta unit build. Problem solving etc etc]]> https://www.soliforum.com/post/65323/#p65323 All seems good form the photos. You'd be looking for anything missing teeth or obviously amiss in the gearbox. The grease you have on hand is fine for the trust bearing, and it does nto need to be removed to be lubricated.

Wear mark on the wood is not a problem.

]]> Thu, 04 Sep 2014 02:45:51 +0000 https://www.soliforum.com/post/65323/#p65323 <![CDATA[Re: 'struder noob Beta unit build. Problem solving etc etc]]> https://www.soliforum.com/post/65317/#p65317 Ok, assuming that this is actually the thrust bearing:
http://i.imgur.com/OZN3VYt.jpg

What kind of lubrication should I be using? I've got a can of the lithium grease for the printer, would that do?
Oh and does one have to remove the bearing to lube it?

As to the gearmotor, here it is: Not sure if there's anything amiss as I've never looked inside one that was performing properly.
http://i.imgur.com/m1h60nl.jpg

I did see this, what looks to be a wear mark, perhaps the noise was the bearing rotating against it?
http://i.imgur.com/LoyY7F7.jpg

And just a pic of everything so we can be sure I'm not missing everything.
http://i.imgur.com/rXI5FfR.jpg

]]> Thu, 04 Sep 2014 01:44:44 +0000 https://www.soliforum.com/post/65317/#p65317 <![CDATA[Re: 'struder noob Beta unit build. Problem solving etc etc]]> https://www.soliforum.com/post/65310/#p65310 Excellent!
Yeah, I dried it in the oven for about 2 hours at 80 and have had it sat on a heater most of the time in a plastic container packed with every desiccant I've ever acquired tongue

Right, I'll run it for a while today just to make sure it's still actually working then I'll take it apart to check for issues.
I assume the screws on the back(?) of the gear motor are how to access it's guts?

As to drilling, yeah, I'll have to find a drill press somewhere but that is the plan.
Though I'll try lowering my temp down by 10 to see if I can't get it a little bigger without having to drill.

]]> Thu, 04 Sep 2014 00:01:27 +0000 https://www.soliforum.com/post/65310/#p65310 <![CDATA[Re: 'struder noob Beta unit build. Problem solving etc etc]]> https://www.soliforum.com/post/65256/#p65256 Serin wrote:

Replaced my rather hackslash fan holder.. still rather hackslash but it's the best I could do with what I've got sitting around, and apparently it works rather well.

That's all that matters!

Serin wrote:

Getting seemingly consistent diameter between 1.29 to 1.31mm

That's good. Did you predry the PLA? If so, you may need to drill out the nozzle to 1.8 or 1.9mm. Work your way up slowly.

Serin wrote:

My only current queries are about the rather disturbing noise that one can hear towards the end of this clip and the

Not normal. Check the thrust bearing and gearbox internals for damage. Lubricate thrust bearing. If noise persists, cross your fingers and hope for the best. I can get you a new gearmotor if needed.

Serin wrote:

sound from the motor varying a lot as if the voltage isn't a constant even though it's plugged straight into the wall. This seems to coincide with the 'out' light clicking off and on.

Normal. The power supply voltage only varies a few percent, but the human ear is very sensitive to frequency shifts so a change of a few percent in motor speed is audible. It makes a very small impact on filament diameter, nearly negligible. If you're pursuing extremely tight tolerances, you can move them to separate supplies. Even the best 6 amp supplies dip when a 3 amp load is dumped on them.

]]> Wed, 03 Sep 2014 14:10:00 +0000 https://www.soliforum.com/post/65256/#p65256 <![CDATA[Re: 'struder noob Beta unit build. Problem solving etc etc]]> https://www.soliforum.com/post/65239/#p65239 Replaced my rather hackslash fan holder.. still rather hackslash but it's the best I could do with what I've got sitting around, and apparently it works rather well.
Getting seemingly consistent diameter between 1.29 to 1.31mm
My only current queries are about the rather disturbing noise that one can hear towards the end of this clip and the sound from the motor varying a lot as if the voltage isn't a constant even though it's plugged straight into the wall. This seems to coincide with the 'out' light clicking off and on.

https://www.youtube.com/watch?v=thL5734m9LI&

I'm assuming both are probably not healthy...

]]> Wed, 03 Sep 2014 07:21:13 +0000 https://www.soliforum.com/post/65239/#p65239 <![CDATA[Re: 'struder noob Beta unit build. Problem solving etc etc]]> https://www.soliforum.com/post/65148/#p65148 I think that guide is awesome... I like your "get-to-itivness"
Happy to see you have it working.  Now If you just had a filawinder, Hmmm.

]]> Tue, 02 Sep 2014 15:26:37 +0000 https://www.soliforum.com/post/65148/#p65148 <![CDATA[Re: 'struder noob Beta unit build. Problem solving etc etc]]> https://www.soliforum.com/post/65133/#p65133 It's alive!
Still need to rig up a proper guide....

http://i.imgur.com/HEvqA7U.jpg

]]> Tue, 02 Sep 2014 10:38:20 +0000 https://www.soliforum.com/post/65133/#p65133 <![CDATA[Re: 'struder noob Beta unit build. Problem solving etc etc]]> https://www.soliforum.com/post/65120/#p65120 wardjr wrote:

I am jealous wink

Don't worry, if I get bored of making super cheap filament I'll send it over >:D

]]> Tue, 02 Sep 2014 05:44:28 +0000 https://www.soliforum.com/post/65120/#p65120 <![CDATA[Re: 'struder noob Beta unit build. Problem solving etc etc]]> https://www.soliforum.com/post/65114/#p65114 I am jealous wink

]]> Tue, 02 Sep 2014 04:50:58 +0000 https://www.soliforum.com/post/65114/#p65114