<![CDATA[SoliForum - 3D Printing Community — Running an AMA over on Reddit for Kickstarter/Filastruder...]]> https://www.soliforum.com/topic/7285/running-an-ama-over-on-reddit-for-kickstarterfilastruder/ Tue, 12 Aug 2014 23:23:06 +0000 PunBB <![CDATA[Re: Running an AMA over on Reddit for Kickstarter/Filastruder...]]> https://www.soliforum.com/post/63066/#p63066 +1

]]> Tue, 12 Aug 2014 23:23:06 +0000 https://www.soliforum.com/post/63066/#p63066 <![CDATA[Re: Running an AMA over on Reddit for Kickstarter/Filastruder...]]> https://www.soliforum.com/post/63037/#p63037 wardjr wrote:

I also would like to take a moment to thank you for everything you do for this community.  I would not be anywhere near where I am in the world of 3D printing if not for you pushing me to learn and figure some things out on my own.

+1...Thank you, Tim!

I also read through your reddit post and I'm sure your writeup will help many others with KS plans...I always felt that KS ideally should be used as a tool for the funding of raw materials, component purchasing, and validation of customer demand (pre-orders)...and not about developing the product itself...granted, some ideas truly need funding dollars to get to a preferred design; but preferably and to your point, a KS design should be nailed prior to kick-off!

I wish you continued success!

]]> Tue, 12 Aug 2014 17:39:05 +0000 https://www.soliforum.com/post/63037/#p63037 <![CDATA[Re: Running an AMA over on Reddit for Kickstarter/Filastruder...]]> https://www.soliforum.com/post/63008/#p63008 I read through it last night and found it to be spot on accurate as to the failures that we see so often on KS.
You did a very nice job of being clear and concise as to what it takes to be successful.  Hopefully others will take the time to read that before launching a campaign destined to fail.   

I also would like to take a moment to thank you for everything you do for this community.  I would not be anywhere near where I am in the world of 3D printing if not for you pushing me to learn and figure some things out on my own.

]]> Tue, 12 Aug 2014 14:54:22 +0000 https://www.soliforum.com/post/63008/#p63008 <![CDATA[Re: Running an AMA over on Reddit for Kickstarter/Filastruder...]]> https://www.soliforum.com/post/63005/#p63005 Reddit is blocked at work or I would have been there.  +1 on support level you have for your product and solidoodle.  Very admirable.

]]> Tue, 12 Aug 2014 14:48:27 +0000 https://www.soliforum.com/post/63005/#p63005 <![CDATA[Re: Running an AMA over on Reddit for Kickstarter/Filastruder...]]> https://www.soliforum.com/post/63004/#p63004 Thanks, that means a lot!

]]> Tue, 12 Aug 2014 14:44:44 +0000 https://www.soliforum.com/post/63004/#p63004 <![CDATA[Re: Running an AMA over on Reddit for Kickstarter/Filastruder...]]> https://www.soliforum.com/post/62983/#p62983 I saw your AMA and noticed that you wanted to keep it about the Kickstarter/Filastruder, but I just wanted to thank you for everything that you've done for this community. Thank you for not only developing and releasing an incredible product aimed at  helping everyone here, but for the continued support that you provide. You're a huge reason that I'm still on these forums and trudging along with my doodle. Thank you again for your support of us noobs. It's greatly appreciated.

]]> Tue, 12 Aug 2014 12:12:17 +0000 https://www.soliforum.com/post/62983/#p62983 <![CDATA[Running an AMA over on Reddit for Kickstarter/Filastruder...]]> https://www.soliforum.com/post/62911/#p62911 http://www.reddit.com/r/3Dprinting/comm … d_212k_on/

Chime in if you like!

]]> Mon, 11 Aug 2014 16:42:20 +0000 https://www.soliforum.com/post/62911/#p62911