<![CDATA[SoliForum - 3D Printing Community — first day at the 3d printer]]> https://www.soliforum.com/topic/7246/first-day-at-the-3d-printer/ Tue, 19 Aug 2014 04:45:45 +0000 PunBB <![CDATA[Re: first day at the 3d printer]]> https://www.soliforum.com/post/63719/#p63719 tonycstech wrote:

320c heat bed ? no way ! Thats hotter then nozzle.
I'd like to  have that temperature when printing ABS smile
Permanent warp solution L)

right
, my bad
, thats the extruder temp...the set  up for the heat bed is 60 for pla  and 120(ithink) for ABS..

]]> Tue, 19 Aug 2014 04:45:45 +0000 https://www.soliforum.com/post/63719/#p63719 <![CDATA[Re: first day at the 3d printer]]> https://www.soliforum.com/post/63718/#p63718 320c heat bed ? no way ! Thats hotter then nozzle.
I'd like to  have that temperature when printing ABS smile
Permanent warp solution L)

]]> Tue, 19 Aug 2014 04:40:04 +0000 https://www.soliforum.com/post/63718/#p63718 <![CDATA[Re: first day at the 3d printer]]> https://www.soliforum.com/post/63716/#p63716 tonycstech wrote:

LOL 1st picture is like print quality evolution LOL
What kind of printer is this, is it any good ?
What is its max build volume and does it have direct feed or bowden feed ?
HEat bed ?

thanks !


its an AirWold HDx, im not sure if is any good, its the first and only 3d printer i have ever seen and use,,,so i have nothing to compare it with but so far so good... it has nice LED lights..
here you can read abut this printer

http://airwolf3d.com/store/products/lar … l-aw3d-hd/

heat bed, sure up to 320 C...
cheers!

]]> Tue, 19 Aug 2014 03:49:32 +0000 https://www.soliforum.com/post/63716/#p63716 <![CDATA[Re: first day at the 3d printer]]> https://www.soliforum.com/post/63649/#p63649 LOL 1st picture is like print quality evolution LOL
What kind of printer is this, is it any good ?
What is its max build volume and does it have direct feed or bowden feed ?
HEat bed ?

thanks !

]]> Mon, 18 Aug 2014 04:56:08 +0000 https://www.soliforum.com/post/63649/#p63649 <![CDATA[first day at the 3d printer]]> https://www.soliforum.com/post/62559/#p62559 so i figure the best way to learn, is to start small and build on to that... so most of the day i try to print this basic pieces i did in cinema, after alot of basic mistakes, once i got this 1cm pz (4 in) righ i "push it a little"and try the same piece on half the scale..wich is close to the printer specs....,  .5cm ( 2 in)... at the end i was very happy with both results..... so tomorrow i can move on to bigger more complex shapes.... i share some pictures and screen captures of this process,,, very helpful practice

http://2.bp.blogspot.com/-nV9gSrpHxRo/U-QVIgCxAaI/AAAAAAAAAKM/g4RKweJ4-Uo/s1600/20140807_181323.jpg

http://3.bp.blogspot.com/-lGrtfe8B4JE/U-QVJTIlfhI/AAAAAAAAAKU/YtETjJPGfss/s1600/20140807_181535.jpg

http://3.bp.blogspot.com/-jXelVZR86dQ/U-QVJcfoqDI/AAAAAAAAAKY/PPJ__DcYFgw/s1600/20140807_181657.jpg

http://2.bp.blogspot.com/-c1CoO0rgs44/U-QWPZZxwnI/AAAAAAAAAKs/OAGgb1W9oHw/s1600/captura.JPG

http://4.bp.blogspot.com/-fC-RkbF3mQI/U-QVKWU3meI/AAAAAAAAAKk/r6vHCykogNw/s1600/20140807_181721.jpg

]]> Fri, 08 Aug 2014 00:16:53 +0000 https://www.soliforum.com/post/62559/#p62559