<![CDATA[SoliForum - 3D Printing Community — X stopped working after VREF tweak]]> https://www.soliforum.com/topic/7070/x-stopped-working-after-vref-tweak/ Thu, 14 Aug 2014 17:58:34 +0000 PunBB <![CDATA[Re: X stopped working after VREF tweak]]> https://www.soliforum.com/post/63286/#p63286 Any ground on the board will work.

]]> Thu, 14 Aug 2014 17:58:34 +0000 https://www.soliforum.com/post/63286/#p63286 <![CDATA[Re: X stopped working after VREF tweak]]> https://www.soliforum.com/post/63285/#p63285 So I installed the new drivers and they seem to be working, however when I went to use the multimeter, I slipped and shorted one out. Good think I bought extra. I basically did the same thing as the wiki instructs, but I think that's how I burned the stock driver out. Is there a safer place to put the negative lead from the multimeter? I know the positive goes in the little notch I have circled on the attached pic, but is there a better place for the negative that won't short the driver out? Otherwise the only option is by ear.

Thanks!

]]> Thu, 14 Aug 2014 17:54:54 +0000 https://www.soliforum.com/post/63285/#p63285 <![CDATA[Re: X stopped working after VREF tweak]]> https://www.soliforum.com/post/62843/#p62843 Thanks, Adrian. I'm going to give this a try as soon as the steppers arrive.

]]> Sun, 10 Aug 2014 21:25:11 +0000 https://www.soliforum.com/post/62843/#p62843 <![CDATA[Re: X stopped working after VREF tweak]]> https://www.soliforum.com/post/62804/#p62804 Just go to the manual tab and type in something similar to:
M92 X80.00 Y88.00 Z1000.00 E990.00

adjusting the values as required of course smile M501 will tell you what they are at the moment.

You then type M500 to store those values in EEPROM.
M501 will read back all current values in the EEPROM; just retype the various lines to adjust them and then M500 to store.
The messages appear in repetiers log window of course btw.

If you want help on a specific G-code; http://reprap.org/wiki/G-code is a handy reference

]]> Sun, 10 Aug 2014 15:16:22 +0000 https://www.soliforum.com/post/62804/#p62804 <![CDATA[Re: X stopped working after VREF tweak]]> https://www.soliforum.com/post/62802/#p62802 Hi Adrian,
Yes I am on a Mac so the EEPROM window doesn't come up. So what exactly would I type in the manual G-Code field in Repetier to change all 4? Sorry, just don't want to screw it up. Thanks.

]]> Sun, 10 Aug 2014 14:54:49 +0000 https://www.soliforum.com/post/62802/#p62802 <![CDATA[Re: X stopped working after VREF tweak]]> https://www.soliforum.com/post/62799/#p62799 you only need to change the steps-per-mm in EEPROM ; either via repetier's dialog (non-mac) or via the M50X commands (on a mac).

]]> Sun, 10 Aug 2014 14:26:23 +0000 https://www.soliforum.com/post/62799/#p62799 <![CDATA[Re: X stopped working after VREF tweak]]> https://www.soliforum.com/post/62798/#p62798 Hi guys,
I was hoping someone could just check my steps to make sure I wasn't missing anything while replacing my 1/16 stepper drivers to the DVR8825 drivers. Here is what I'm planning to do:

1. I bought 4 new drivers on recommendation from Pololu here: http://www.eckertech.com/pololu-drv8825 … ed-tested/
2. Replace all 4 drivers on the board
3. Multiply all 4 numbers by 2 in this line of the configuration.h file - #define DEFAULT_AXIS_STEPS_PER_UNIT   {88,88,2268,96.6}  //{SD Patch} // default steps per unit for ultimaSker


Is there anything I'm missing? I didn't see any other steps on the forum. Thanks for your help.

]]> Sun, 10 Aug 2014 14:23:51 +0000 https://www.soliforum.com/post/62798/#p62798 <![CDATA[Re: X stopped working after VREF tweak]]> https://www.soliforum.com/post/61221/#p61221 For that one you need to solder on the pins.  Put the pins through the board heat a pin near the board.  Touch the solder to the pin at the board and when it's hot enough it should flow nicely into the hole around the pin.  Repeat till your done.

]]> Sat, 26 Jul 2014 00:35:38 +0000 https://www.soliforum.com/post/61221/#p61221 <![CDATA[Re: X stopped working after VREF tweak]]> https://www.soliforum.com/post/61218/#p61218 I got my stepper driver today. I just want to make sure I'm installing it correctly. It looks like I need to solder the pins onto the new board. I'm not great with a soldering iron and with 8 small pins on each side, I can't imagine I won't get some solder on something. Is this right? Thanks.

]]> Fri, 25 Jul 2014 23:27:09 +0000 https://www.soliforum.com/post/61218/#p61218 <![CDATA[Re: X stopped working after VREF tweak]]> https://www.soliforum.com/post/61194/#p61194 That one will work all you need to do is change the steps in EEPROM (double).
You should be able to just pull the old one out and plug in the new one.

]]> Fri, 25 Jul 2014 15:13:40 +0000 https://www.soliforum.com/post/61194/#p61194 <![CDATA[Re: X stopped working after VREF tweak]]> https://www.soliforum.com/post/61186/#p61186 I ordered a new stepper driver. Thanks for that. Everything I have been reading about replacing them says they just pop off. Can anyone give me specific advice on how/where to leverage something to pop it off? I really don't feel like breaking anything else. If this works, I will upgrade to the 1/32 drivers although I believe I will have to change something in the code and upload the firmware change, correct? Would this be the right one? http://www.pololu.com/product/2133

Thanks.

]]> Fri, 25 Jul 2014 12:19:10 +0000 https://www.soliforum.com/post/61186/#p61186 <![CDATA[Re: X stopped working after VREF tweak]]> https://www.soliforum.com/post/61150/#p61150 Good time to upgrade to an 8825.

]]> Fri, 25 Jul 2014 00:15:16 +0000 https://www.soliforum.com/post/61150/#p61150 <![CDATA[Re: X stopped working after VREF tweak]]> https://www.soliforum.com/post/61101/#p61101 Just the daughterboard, they're like $10 from pololu.

http://www.pololu.com/product/1182

]]> Thu, 24 Jul 2014 14:23:40 +0000 https://www.soliforum.com/post/61101/#p61101 <![CDATA[Re: X stopped working after VREF tweak]]> https://www.soliforum.com/post/61100/#p61100 I adjusted it exactly to what the Wiki suggests and it's still not responding. If I did somehow short it out, do I have to replace the whole board or would it just be the steppers?

]]> Thu, 24 Jul 2014 14:08:13 +0000 https://www.soliforum.com/post/61100/#p61100 <![CDATA[Re: X stopped working after VREF tweak]]> https://www.soliforum.com/post/61089/#p61089 Or, if you used a metal screwdriver, you could have shorted out a spot on your printer board. Best to use a non-conductive screwdriver for those adjustments on the board.

]]> Thu, 24 Jul 2014 11:49:16 +0000 https://www.soliforum.com/post/61089/#p61089